SOLARFOCUS ecotop light Installation Manual Download Page 24

Page: 24 / 32

7 Electrical connection

X61 Differential pressure gauge

> 29

optional

X6 Spare

X21 Safety chain 230 V AC (EMERGENCY OFF

switch, if necessary connect through pressure
sensor,...in series)

> 25

X28 External boiler request

> 24

X29 Fault

> 25

X51 External request (optional)

> 25

X54 External bus line; connection for RS-485 elec-

tronic modules

X55 External bus line; connection for CAN bus elec-

tronic modules

7.2.1 Connect heating circuit pump(X9, X10)

►

Connect heating circuit pump 1 to power section
connector

, connect heating circuit pump 2 to

X10

►

If required (e.g. for underfloor heating), connect a
limiting thermostat (art. 61612).

►

If no limiting thermostat is used, the contact must
be bridged.

7.2.2 Pellet conveyor system (X14)

Extraction system direct extraction auger

►

Connect the motor of the screw conveyor to
power unit X14, use cable 5x1.5 mm

5-pin connector, direct

extraction motor

Terminal

X14

on the power element

PE (1)

N (2)

L (3)

TK(4)

TK (5)

OEM system

Use e.g. for pellet box transfer unit auger and for the

pellet mole

(these systems have a motor–thermal pro-

tection is integrated).

►

Bridge the two TK terminals on the boiler power
element.

►

Use 3 x1.5 mm² cable

7.2.3 External boiler request (X28)

Potential-free Relay output for switching an external
boiler, for example, an external boiler is controlled by
the SOLARFOCUS boiler control.

CAUTION

– The connection is floating and

has a maximum load of 5 A.

Installation manual

ecotop-zero, ecotop-light

Summary of Contents for ecotop light

































Search results

Summary of Contents for ecotop light

Reviews:

Related manuals for ecotop light

Brands by name

Popular brands

SOLARFOCUS ecotop light, Installation Manual

Search results

Summary of Contents for ecotop light

Reviews:

Related manuals for ecotop light

Brands by name

Popular brands