background image

Chapter 6: Communication Setup 

SolarEdge Installation Guide - MAN-01-00060-2.6 

43 

Chapter 6: Configuring 
communication 

power optimizers send information to the inverter via the DC power supply lines (the output circuit PV). No wires or 
configuration is required for this purpose. The information is then sent from the inverter to the SolarEdge Monitoring 
Portal Internet. To send data from the inverter, a communication link to be established, as described in this chapter. 
The configuration of the communication is not required for the recovery of energy and is only required to use the 
SolarEdge Monitoring Portal. This chapter also describes the configuration of the communication between multiple 
inverters to a master / slave configuration.

WARNING : 

When connecting communication cables, be sure that the ON / OFF switch at the base of the inverter is in the OFF position, and the CA is in the 
OFF position. When configuring communication parameters, make sure the ON / OFF switch is in the OFF position, and the CA is ON.

communication connectors 

Two glands communication are used for various communication options of the inverter. Each gland has three 
openings. The table below describes the fo nctionnalités ch at that opening. Unused openings must remain sc she is. 

openings. The table below describes the fo nctionnalités ch at that opening. Unused openings must remain sc she is. 

openings. The table below describes the fo nctionnalités ch at that opening. Unused openings must remain sc she is. 

openings. The table below describes the fo nctionnalités ch at that opening. Unused openings must remain sc she is. 

openings. The table below describes the fo nctionnalités ch at that opening. Unused openings must remain sc she is. 

Cable gland Opening # 

functionality 

Cable size (diameter) 

1 (PG16) 

A small 

External antenna cable ( ZigBee, Wi-Fi)

External antenna cable ( ZigBee, Wi-Fi)

2-4 mm 

two large 

Ethernet (CAT5 / 6) 

4.5 to 7 mm 

2 (PG13.5) 

trios 

RS485, power reduction, electric meters 

From 2.5 to 5 mm 

Figure 16: Communication Cable glands 

Summary of Contents for SE10k
















































































Reviews: