background image

- 28 -

15. Warranty

SolarAttic

Limited Warranty-PCS

All Pool Convection System (PCS) pool heaters are warranted to be free from manufacturing defects for
a period of thirty-six (36) months from the date of first consumer installation or fifty-four (54) months
from the date of shipment from the factory, whichever occurs first.  The consumer must complete and
return the warranty registration card and provide a receipted bill of sale as proof of warranty period
within 30 days from the date of installation.  Without registration and proof of purchase date, the war-
ranty begins on the date of shipment from the factory.  This Limited Warranty covers parts and labor to
correct manufacturing defects only.  It does not cover incidental fin damage nor any corrosive damage
to heat transfer coils caused by improperly maintained chemical levels in pools.  Ph levels outside the
7.2 to 7.6 range voids warranty.  Use in Ocean or Sea water pools voids warranty.  Use in pools utiliz-
ing salt, as a source of chlorine, does not void warranty.  All chemical dispensers must be plumbed
downstream.  Dispensing pool chemicals directly into the pool heater voids warranty.  Failure to proper-
ly winterize the pool heater in areas with freezing temperatures voids warranty.  This warranty does not
cover winter freeze damage, normal maintenance, labor charges for removal or installation of parts,
transportation charges to the factory or for any other service calls or repairs.

Corrugated fins are used on the heat transfer coils for improved efficiency.  They are waffled in appear-
ance and not straight.  Fin bending that has been combed with a fin tool does not affect performance
and is not considered a manufacturing defect.  Our obligation under this warranty is limited to the repair
or replacement, at our factory, of any part which, upon our examination, has proven to be defective.
Correction of such defects by repair or replacement (at our option) and return freight via lowest com-
mon carrier, shall constitute fulfillment of SolarAttic’s obligation.  This warranty does not apply to
those products which, in SolarAttic’s  judgment, have been altered or repaired outside of our factory or
by unauthorized factory representatives, subjected to misuse, negligence, accident, corrosive atmos-
pheres, or operating beyond the limits of our design.

THIS WARRANTY CONSTITUTES THE BUYERS SOLE REMEDY.  IT IS GIVEN IN LIEU OF ALL OTH-
ER WARRANTIES.  THERE IS NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE.  WHERE CIRCUMSTANCES CAUSE REMEDY EXPRESSED HEREIN TO
FAIL OF ITS ESSENTIAL PURPOSE, SOLARATTIC’S LIABILITY SHALL NOT IN ANY EVENT EX-
CEED THE ORIGINAL PURCHASE PRICE.  IN NO EVENT, SHALL SOLARATTIC BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, WHETHER THE THEORY BE BREACH OF THIS OR
ANY OTHER WARRANTY, NEGLIGENCE, OR STRICTLY TORT.  DISPUTES ARISING UNDER THIS
AGREEMENT SHALL BE GOVERNED BY APPLICABLE MINNESOTA LAW.  THE VENUE FOR ALL
DISPUTES IS SWIFT COUNTY, MINNESOTA.

Model Number _________________________________________ 

Serial Number__________________________________________

Date of Installation ______________________________________  

Installer _______________________________________________

______________________________________________________

Summary of Contents for PCS3

































Reviews: