Solar Roofs SkyLine 200152C80EX Installation Manual Download Page 7

Page: 7 / 31

2.1.2.

Components Included with the SolarRoofs Type 5

PV Panel

PV Panel brackets

Bracket hardware

PV panel wire PV switch

12 Volt Pump

Tempering Valve assembly

Check valve

Dielectric Unions

Tank Nipples

Solar Loop Pressure Gauge

Expansion tank

(pre

charge to 38 lb.)

Expansion tank copper assembly

Pump head

with 1/2” male fitting

Cool feed assembly bracket

50’ Roll of 1/2 OD copper

Cool feed line

compression

union

Cool feed lower brass

assembly and temp gauge

Cool feed line

compression union

Hot return assembly with

temperature gauge an

check valve

Antifreeze

(not included)

Top charging fill valve V1

(with cap)

Isolation ball valve V3

Bottom charging fill valve V2

(with cap)

Cool feed tank to un

ion adaptor

1” square tube mounting rails

(2 collector system shown)

6 mounting rail brackets with

6 lags and 6 washers for every

system rail set

Collector component

Assembly:

Air vent

Pressure relief valve

Upper comp. unions 2 90s and 1

straight

Center comp

ression union body

Lower compression 90 union

Color coded bracket

“tec screws”

2 Color codes roof boots

3 Collector U clips

(per extra collector)

System documents and

lab

els

Mixing valve only included with kit, assembly is

included in picture to illustrate complete assembly

or Coin Vent

Please Note:

SolarRoofs has improved its system and some pictures will not be visually

accurate but show all the components included. Most copper fittings have been replaced

with Brass. More visually accurate pictures will be included in their sections.

Summary of Contents for SkyLine 200152C80EX
































Search results

Summary of Contents for SkyLine 200152C80EX

Reviews:

Related manuals for SkyLine 200152C80EX

Brands by name

Popular brands

Solar Roofs SkyLine 200152C80EX, Installation Manual

Search results

Summary of Contents for SkyLine 200152C80EX

Reviews:

Related manuals for SkyLine 200152C80EX

Brands by name

Popular brands