manualshive.com logo in svg

Solahart 151J, Owner'S Manual

The Solahart 151J Owner's Manual is the go-to resource for maximizing the potential of your solar water heater. This comprehensive manual is available for free download on our website, providing detailed instructions and insights for efficient use. Unlock the full potential of your Solahart system today! Download it from manualshive.com.

Share
Download
background image

 

20 

INSTALLATION INSTRUCTIONS - ALL MODELS 

 

General 

INSTALLATION STANDARDS 

The water heater must be installed: 

•

 

by a qualified person, and 

•

 

in accordance with the installation instructions, and 

•

 

in  Australia,  in  compliance  with  the  Plumbing  Code  of  Australia (PCA),  Standards  AS/NZS 3500.4  and 
AS/NZS 3000, and all local codes and regulatory authority requirements, or 

•

 

in other countries, in compliance with national and local codes and regulatory authority requirements. 

•

 

in New Zealand also conforming to Clauses G12 and H1 of the New Zealand Building Code. 

 

  Warning:

  This  water  heater  may  deliver  water  at  high  temperature.  Refer  to  the  Plumbing  Code  of  Australia,  local 

requirements and these installation instructions to determine if additional delivery temperature control is required. 
 

INSTALLATION MUST COMPLY WITH LOCAL ELECTRICAL AND PLUMBING CODES 

 

Victorian Installers 

Notice to Victorian Installers from the Victorian Building Authority if this solar water heater is installed in a new Class 1 
dwelling in the State of Victoria. The system model number is to be recorded on the Certificate of Compliance. It is also a 
requirement to provide the householder with permanent documentation recording the system model number exactly as it is 
shown  in  the  ‘VEET  Product  Register’  published  by  the  Essential  Services  Commission  in  Victoria.  See  www.veu-
registry.vic.gov.au/Public/ProductRegistrySearch.aspx.  This  documentation  may  be  in  the  form  of  an  indelible  label 
adhered to the solar storage tank, or other suitable form placed in an accessible location, such as the meter box, for later 
inspection. 
 

WATER HEATER APPLICATION 

This water heater is designed for the purpose of heating potable water. Its use in an application other than this may shorten 
its life. 
 
If this water heater is to be used where an uninterrupted hot water supply is necessary for the application or business, then 
there  should  be  back-up  redundancy  within  the  hot  water  system  design.  This  should  ensure  the  continuity  of  hot  water 
supply in the event that this water heater was to become inoperable for any reason. We recommend you provide advice to 
the system owner about their needs and building back-up redundancy into the hot water supply system.

 

 

LOCATION 

The solar water heater should be installed close to either the most frequently used outlet or the previously installed water 
heater in a retrofit installation if existing pipe work is to be utilised, and its position chosen with safety and service in mind. 
The water heater must be installed in an area that is free of shade all year round. Ensure that trees do not shade the water 
heater, particularly in winter. 
 
NOTE:  Sufficient  space  should  be  left  around  the  thermosiphon  solar  water  heater  to  allow  for  safe  service  access.  A 
distance  equal  to  the  length  of  the  tank  should  be  left  at  the  water  supply  connections  end  of  the  tank  to  any  wall  or 
obstruction  so  that  the  anode  can  be  removed  and  replaced  during  a  service.  In  addition,  a  minimum  of  one (1)  metre 
clearance  is  recommended  to  be  left  around  the  solar  storage  tank  and  solar  collectors  on  the  other  three  sides  for  safe 
service access. 
 

 

Warning

:  The  water  heater  must  be  installed  on  an  adequately  supported  area  of  roof.  In  cyclone  areas  additional 

mounting restraints are required 
 
Refer to the Technical Specifications section for the weight of the water heater. It is advisable that the weight of the water 
heater be braced to a load bearing wall. If in any doubt of the construction or the condition of the roof, obtain advice from a 
registered  builder  or  structural  engineer.  The  installer  must  ensure  that  the  structural  integrity  of  the  roof  is  not 
compromised by the installation of the solar water heater. 
 
In areas susceptible to cyclones, hurricanes or very high winds, a suitable With Pitch frame is required. Refer to your local 
Solahart Dealer for details. 
 

Summary of Contents for 151J





























































Reviews:

No comments

Related manuals for 151J

Marta MT-2524 User Manual preview
MT-2524
Brand: Marta Pages: 12
Lasko 6435 Important Instructions & Operating Manual preview
6435
Brand: Lasko Pages: 4
A.O. Smith 970 Series Parts List preview
970 Series
Brand: A.O. Smith Pages: 8
Rinnai ES38 RHFE-1004FTA Conversion Manual preview
ES38 RHFE-1004FTA
Brand: Rinnai Pages: 12
A.O. Smith FREZYA 200S User Manual preview
FREZYA 200S
Brand: A.O. Smith Pages: 48
CobraCo FB8003 Owner'S Manual preview
FB8003
Brand: CobraCo Pages: 4
Annovi Reverberi RSV 3400 Operating Instructions And Parts Manual preview
RSV 3400
Brand: Annovi Reverberi Pages: 16
Funkyheat TOUCHSCREEN FAR Instruction & Installation Manual preview
TOUCHSCREEN FAR
Brand: Funkyheat Pages: 26
Pfeiffer Vacuum SMARTVANE 55 Operating Instructions Manual preview
SMARTVANE 55
Brand: Pfeiffer Vacuum Pages: 68
Rowenta SEMI SHIELDED BU5510 Instructions For Use Manual preview
SEMI SHIELDED BU5510
Brand: Rowenta Pages: 16
Consort PHSL2 Series Installation & Control Manual preview
PHSL2 Series
Brand: Consort Pages: 4
EBARA EVMSN3 Operating And Maintenance Manual preview
EVMSN3
Brand: EBARA Pages: 172
ThermoFlow Elex 10 Installation Manual, User Manual, And Warranty Information preview
Elex 10
Brand: ThermoFlow Pages: 34
A.O. Smith del and del Installation & Operation Manual preview
del and del
Brand: A.O. Smith Pages: 16
Olimpia splendid CALDOSTILE D Instructions For Installation, Use And Maintenance Manual preview
CALDOSTILE D
Brand: Olimpia splendid Pages: 52
Watson Marlow Pumps 604U Manual preview
604U
Brand: Watson Marlow Pumps Pages: 13
Alemite 9616-A Service Manual preview
9616-A
Brand: Alemite Pages: 10
WaterGroup E75TFC-3 Installation, Operation And Service Manual preview
E75TFC-3
Brand: WaterGroup Pages: 24

Brands by name

Popular brands

Load more brands