manualshive.com logo in svg

Sola 0610-010KA, Installation And Operation Manual

Share
Download
Sola 0610-010KA Installation And Operation Manual Download Page 34

SOLA 610 UPS Optional Features

To install the AS 400® card complete the following :-

1.

Shutdown the UPS, turn the UPS OFF and remove the
input line cord from the wall socket. If the UPS is hard
wired, isolate the UPS at the supply point and make safe.

CAUTION : Even with the UPS switched off
dangerous voltages may still be present at
the UPS or its outlets.

2.

Remove the communications slot cover on the rear of the
UPS by removing the two retaining screws. Slide the
AS400® card option into the slot and secure it with
supplied screws.

3.

Store the communications slot cover plate for
reinstallation should the AS400® card option be removed
and decommissioned in the future.

4.

The AS400® card will now be operational when the UPS
is turned on and returned to service.

Output 2 (ES 2 Pin connector)

4.4    Installation and Operation of the  AS400® card
option

!

26

A plug with link is supplied with the AS400® card option. This
plug must be installed for normal operation. If this plug is
removed, the load will be transferred to bypass.

The plug is removed only in applications where an external
maintenance bypass switch is used (refer to instructions
provided with the optional external maintenance bypass switch).

1

2

3

4

5

6

7

8

9

Remote Shutdown -

Remote Sh

Summary Alarm

UPS Fail

Bypass Active

Battery Low

UPS ON

Utility Fail

Summary of Contents for 0610-010KA











































Reviews:

No comments

Brands by name

Popular brands

Load more brands