SOFTSTARTUK MIP-6 Instruction Manual Download Page 28

28 • Control Keypad 

 

________________________________________________________________________________________________ 

21 YEARS DATA 

--****--

 

 

Display  

Description 

YEAR=06 
60.0 MOHM 
 

Previous year data. 
 
Range: 0 – 60MOhm.

 

YEAR=.. 
45.5 MOHM 
 

Display up to total of 21 screens showing average levels for all previous years 
since commissioning or since resetting of actual data. 
Range: 0 – 60MOhm.

 

 

6.9.10

 

Fault data – page 10 

FAULT DATA 

- **** - 

 

Display and default 

values 

Description 

LAST TRIP 
INTERNAL FAILURE 
 

Displays last active fault that was enabled as a trip. 

LAST ALARM 
INTERNAL FAILURE 
 

Displays last active fault that was enabled as an alarm. 

PRE TRIP INSUL. 
0 KOHM 
 

Displays values of insulation resistance before last trip. 

LAST 10 TRIPS: 
HH:MM         DD/MM/YY 
 

Displays the header of next 10 screens showing the details of last 10 trips with 
time stamps. hour: minutes   Day/Month/Year 

INSULATION TRIP 
18:00       16/07/07 
 

Displays last trip with its time stamp. 

EXTERNAL FAULT 1 
18:00       16/07/07 
 

Displays previous trip with its time stamp. 

EXTERNAL FAULT 2 
19:00       17/07/07 
 

Displays previous trip with its time stamp. 

NO DATA 
 
 

Displays in case no fault data exist. 

 

 

Summary of Contents for MIP-6

































Reviews: