SOFTSTARTUK MIP-6 Instruction Manual Download Page 24 | Manualshive

Page: 24 / 32

SOFTSTARTUK MIP-6 Instruction Manual Download Page 24

24 • Control Keypad

________________________________________________________________________________________________

6.9.4

Comm. Parameters settings – page 4

COMMUNICATION P.

***SETTINGS***

Display and default

values

Range Description

BAUD RATE
19200

OFF, 19200,
9600, 4800,
2400, 1200

Sets MIP-6 BAUD RATE.
Available only when communication option is installed.

ADDRESS NUMBER
OFF

OFF, 1-247

Sets MIP-6 rear communication ADDRESS LINK NO.
Available only when Communication option is installed.

S.LINK PAR. SAVE
DISABLE

ENABLE
DISABLE

When set to DISABLE, it prevents parameter setting
through serial link communication.
When set to ENABLE, parameter setting through serial link
is enabled.

S.LINK CONTROL
DISABLE

ENABLE
DISABLE

When set to DISABLE, it prevents DO NOT MEASURE,
MEASURE, LINE TEST, REMOTE RESET commands
through serial link communication.
When set to ENABLE, commands through serial link are
enabled.

FRONT COM ADDRES
OFF

OFF, 1-247

This is a future enhancement.

STORE ENABLE
COMM. PARAMETERS

Same as STORE ENABLE INSULATION PARA
On page 18.

«
...
22
23
24
25
26
...
»

Summary of Contents for MIP-6

































Reviews:

No comments