manualshive.com logo in svg

Sofar solar 3K-6KTLM-G2, User Manual

Share
Download
Sofar solar 3K-6KTLM-G2 User Manual Download Page 59

SOFAR 3K~6KTLM-G2

User manual

Copyright © Shenzhen SOFARSOLAR Co., Ltd

- 54 -

screen, the red light will be on, and the fault can be found in the history of
the fault. For the machine installed with Wi-Fi/GPRS, the alarm
information can be seen on the corresponding monitoring website, and can
also be received by the APP on the mobile phone.

EventList information

Table 7-1 Eventlist

EventList

NO.

EventList Name

EventList

description

solution

ID01

GridOVP

The power grid

voltage is too high

If the alarm occurs occasionally, the

possible cause is that the electric grid is

abnormal occasionally. inverter automatically

returns to normal operating status when the

electric grid’s back to normal.

If the alarm occurs frequently, check

whether the grid voltage/frequency is within the

acceptable range. If no, contact technical

support. If yes, check the AC circuit breaker and

AC wiring of the inverter.

If the grid voltage/frequency is within the

acceptable range and AC wiring is correct, while

the alarm occurs repeatedly, contact technical

support to change the grid over-voltage,

under-voltage, over frequency, under-frequency

protection points after obtaining approval from

the local electrical grid operator.

ID02

GridUVP

The power grid

voltage is too low

ID03

GridOFP

The power grid

frequency is too

high

ID04

GridUFP

The power grid

frequency is too low

ID05

PVUVP

The input voltage is

too low

Check whether too few PV modules are

series connected in a PV string, thus the

voltage(Vmp) of the PV string is lower than the

minimum operating voltage of inverter. If yes,

adjust the number of series connected PV

modules to increase the voltage of the PV string

to fit the input voltage range of inverter. inverter

automatically returns to normal operating status

after correct adjustments.

ID06

Vlvrtlow

LVRT function is

faulty

Check whether the grid voltage fluctuates

greatly.

ID07

Vovrthigh

OVRT function is

faulty

ID09

PVOVP

The input voltage is

too high

Check whether too many PV modules are

series connected in a PV string, thus the

voltage(Voc) of the PV string is higher than the

maximum input voltage of inverter. If yes, adjust

the number of series connected PV modules to

decrease the voltage of the PV string to fit the

input voltage range of inverter. inverter

automatically returns to normal operating status

after correct adjustments.

Summary of Contents for 3K-6KTLM-G2
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands