Sofar solar 3K-6KTLM-G2 User Manual Download Page 45

Page: 45 / 79

SOFAR 3K~6KTLM-G2

User manual

- 40 -

RS485

→

USB adapter; connect the USB port of the adapter to the computer. A

maximum of 31 inverters can be connected in one daisy chain. (NOTE2)

Figure 4-35

2. WI-FI/GPRS/Ethernet

Refer to the figure shown below: (wireless function required for the PC).

Figure 4-36

The operation information (generated energy, alert, operation status) of the

inverter can be transferred to PC or uploaded to the server via
WIFI/GPRS/Ethernet. You can register on the website.

http://www.solarmanpv.com/portal/Register/Regi_Pub.aspx

Using the Wi-Fi/GPRS/Ethernet S/N number (NOTE3), then you can login

the website:

http://www.solarmanpv.com/portal/LoginPage.aspx

to remote

monitors the inverter.

Note1:

The length of the RS485 communication cable should be less than 1000 m.

Note2:

When multiple inverters are connected via RS485 wires, set mod-bus address to

differentiate the inverters.

Summary of Contents for 3K-6KTLM-G2
















































































Search results

Summary of Contents for 3K-6KTLM-G2

Reviews:

Brands by name

Popular brands

Sofar solar 3K-6KTLM-G2, User Manual

Search results

Summary of Contents for 3K-6KTLM-G2

Reviews:

Brands by name

Popular brands