Home
/
Soehnle
/
3035
/
Manual

Soehnle 3035, Manual, Page: 140 / 240

Share

Page: 140 / 240

Soehnle 3035 Manual Download Page 140

140

Totaling memory capacity
Up to 999 transaction can be stored in totaling memory.
The totaling memory needs to be deleted thereafter.

Display view
After the first totaling transaction, the display switches from the basic screen Specific Weight to
the Totaling screen, if the "Information Field Display" setting is set to the factory default.

Operating the totaling function
Press the Function Page key to start the Neutral Measurement Functions level 1.

•

Plus F6

Press the Plus key to save the weight on the weighing bridge to the totaling memory. The
item counter and the sequential number are incremented by 1.
Prior to a new totaling transaction, the scale must be relieved by a minimum relief factor
specified in setup mode.
A weight value of 0 or totaling without relieving the scale is displayed with "Error 55 - Place
Weight". The relief factor = 0 only requires a change in weight.
Gross, tare, and net values and unit counts can be totaled.

•

Cancel F5

The Cancel key is used to cancel or reverse weigh individual items. Pressing the Cancel key
is followed by the prompt to either place the weight to be canceled on the scale, or to
enter the sequential number of the weight to be canceled.
Press the key combination Info and F5 Plus for information about the sequential number.
Use the number keypad to enter the sequential number of the item to be canceled and
confirm with F6 Save.
If no sequential number is entered, the weight reading on the scale is saved by pressing the
F6 key. The error message is displayed if the scale is not under load.
Cancellations or reverse weighings are marked in the printed receipt as Cancellation. A
cancellation causes the sequential number to be incremented by one, while the item
counter is decremented by one.
If the item counter is 0, no further cancellations are possible; this is displayed by error
message Error 48.

«
...
138
139
140
141
142
...
»

Summary of Contents for 3035

















































































































































































































































Reviews:

No comments