background image

 

15 

 

BRAKE POSITION 

LEFT HAND BRAKING, 
WITH RIGHT HAND 
RELEASED TURNS UNIT 
TO THE LEFT 

DRIVE POSITION 

TRACTION LEVER POSITION 

SECTION 3 - OPERATING INSTRUCTIONS 

 

WARNING 

Brakes require maintenance. Inspect for proper 
operation before operating machine. Refer to 
Section “ADJUSTMENTS, STEERING AND 
BRAKES”. 

 

3.6

 

TRACTION LOCK OPERATION - 

1.  To “Lock” the Traction Levers, simultaneously 

squeeze both Traction Levers toward the handle. 

2.  Using right thumb, push Traction Lock forward to 

the “Locked” position and hold. Make sure that the 
Traction Lock has fully engaged both Traction 
Levers. See Figure 3.2 and 3.8. 

3.  Carefully and slowly release both Traction Levers. 

Remove thumb from Traction Lock. 

4.  To “Unlock” the Traction Levers, simultaneously 

squeeze both Traction Levers toward the handle. 
The Traction Lock will move to the “Unlocked” 
position. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

FIGURE 3.8 

 
 

WARNING 

Machine should always be in forward motion before 
attempting a turn. DO NOT attempt a turn from a 
stopped position. 

 
 

3.7 TURNING MOWER 

 

GRADUAL RIGHT & LEFT HAND TURN 

 
IMPORTANT: Squeezing the right or left traction lever 
applies the brake to the right or left wheel. The brake 
turns the machine right or left. 
 
1.  
With machine in Forward motion gradually squeeze 

the right hand traction lever. The machine will turn to 
the right. 

2.  With machine in Forward motion gradually squeeze 

the left hand traction lever. The machine will turn to the 
left. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

FIGURE 3.9 

 
 

3.8  MOWING AND TURNING ON 
HILLSIDES

 

1.  Always mow hillsides starting at bottom of hill.  Mow 

across slopes, never up and down.  Exercise 
caution when changing directions on slopes.  DO 
NOT mow steep slopes!
 

 

WARNING 

DO NOT mow on steep slopes. DO NOT use with 
any type rider attachment on slopes. DO NOT park 
machine on slopes.
 

 

2.  Hillside mowing is accomplished by squeezing 

Traction Lever on the UPHILL SIDE of machine.  
This helps reduce side slipping of mower. 

3.  When turning mower on hillsides, always turn 

toward the UPHILL SIDE  of mower for better 
control and balance. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

RIGHT THUMB PUSHING 
TRACTION LOCK LEVER 
FORWARD TO LOCK 

Summary of Contents for SPE361



































Reviews: