Not
for
Reproduction
EN
AR BG CS DA DE ES ET FI FR HR HU IT LT LV NL NO PL PT RO RU SK SL SR SV TR UK
English (original instructions)
WARNING
To reduce the risk of damage and danger,
never clean the tool with pressure washer
or under running water.
WARNING
Store indoors only. Always remove the
battery from mower and charger when
cleaning or storing the tool.
Periodically check all nuts and bolts for
proper tightness to ensure safe operation
of the mower.
Wipe the mower clean with a dry cloth
occasionally. Do not use water.
LUBRICATION
All of the bearings in this product are
lubricated with a sufficient amount of high
grade lubricant for the life of the unit under
normal operating conditions. Therefore, no
further bearing lubrication is required.
WARNING
Always protect hands by wearing heavy
gloves and/or wrapping the cutting edges
of the blade with rags and other material
when performing blade maintenance.
Contact with the blade could result in
serious personal injury.
WARNING
Do not lubricate any of the wheel
components. Lubrication may cause the
wheel components to fail during use, which
could result in serious personal injury to the
operator and/or mower or property damage.
REPLACING THE CUTTING BLADE
See figure 11-12.
NOTE:
Only use authorised replacement
blades. Replace worn or damaged blades
and bolts in sets to preserve balance.
■
Stop the motor and remove the switch key.
Allow blade to come to a complete stop.
■
Remove the battery pack.
■
Turn the mower on its side.
■
Wedge a block of wood between the
blade and mower deck to prevent the
blade from turning.
■
Loosen the blade bolt by turning it
counterclockwise (as viewed from
bottom of mower) using a 27 mm wrench
or socket (not provided).
■
Remove the blade bolt and blade.
■
Place the new blade on the shaft. Ensure
blade is properly seated with shaft going
through center blade hole and the two
blade posts on the fan inserted into their
respective holes on the blade. Make
sure it is installed with the curved ends
pointing up toward the mower deck and
not down toward the ground. When
seated properly, the blade should be flat
against the fan.Thread the blade bolt on
the shaft and finger tighten.
■
Torque the blade bolt down clockwise
using a torque wrench (not provided)
to ensure the bolt is properly tightened.
The recommended torque for the blade
bolt is 62.5~71.5 kgfcm (350-400 in.-lb.).
VERTICAL STORAGE FUNCTION
See figure 13.
■
Remove the battery from the mower.
■
Remove the grass catcher bag.
■
Rotate the handle knobs to the unlocked
position.
■
Lower the handle assembly and rotate
the handle knobs to the locked position.
■
Lift the mower by the front end to the
vertical position.
WARNING
Always remove the battery from the
mower before placing the unit in the
vertical storage position.
STORAGE SWITCH
When the handle is rotated into the fully locked
storage position, the mower is equipped with
a storage switch that will disable the mower
from running in the storage position. The
storage switch does not replace the need to
remove the switch key and battery to prevent
accidental startup or unauthorized use.
10
Summary of Contents for 1696888
