background image

9

200/300 Series

 — VTC eLock Instructions

200/300 Series 

VTC eLock — Manual Programming 

continued

4. 

LCD Contrast 

will be displayed.

5.  Enter 1 - 9 on numeric keypad or 

+/-

 buttons to adjust.

6.  Press “NEXT/SELECT” when done.
7.  Press “BACK/CANCEL” to return to main menu.

LCD Backlight

Using 

LCD BACKLIGHT 

the brightness of the display can be 

adjusted.

1.  Press “MENU.” 

LOGIN PLEASE 

will be displayed.

2.  Scan valid credential or enter 4-14 digit PIN and press 

“ENTER.”

3.  Press “DOWN” button to highlight 

LCD BACKLIGHT 

and press 

“NEXT/SELECT.”

4. 

LCD Backlight 

will be displayed.

5.  Enter 0 - 9 on numeric keypad or 

+/-

 buttons to adjust. 

(“0” = OFF)

6.  Press “NEXT/SELECT” when done.

Set Beep Volume

Using 

SET BEEP VOLUME

, the audible beep can be 

adjusted.

1.  Press “MENU.” 

LOGIN PLEASE 

will be displayed.

2.  Scan valid credential or enter 4-14 digit PIN and press 

“ENTER.”

3.  Press “DOWN” button to highlight 

SET BEEP VOLUME 

and 

press “NEXT/SELECT.”

4. 

Beep Volume 

will be displayed.

5.  Enter 0 - 9 on numeric keypad or 

+/-

 buttons to adjust. 

(“0” = MUTE)

6.  Press “NEXT/SELECT” when done.
7.  Press “BACK/CANCEL” to return to main menu.

Reset Net Schedule

A PROPERLY CONFIGURED AND ENABLED NETWORK eLock 

IS REQUIRED TO MAKE USE OF THIS FEATURE.

Only 

Supervisors

 are allowed to 

RESET NET SCHED

.

Using 

RESET NET SCHED

. the scheduled network check-in 

time can be set.

1.  Press “MENU.” 

LOGIN PLEASE 

will be displayed.

2.  Scan valid credential or enter 4-14 digit PIN and Press 

“ENTER.”

3.  Press “DOWN” button to highlight 

RESET NET SCHED

. and 

press “NEXT/SELECT.”

4. 

NETWORK TIMING RESET 

will be displayed. The eLock will 

follow the programmed or default check-in frequency from 

this time of day forward.

For example:
Programmed Update Interval as set in LockView is 12 hours 

(twice/day). The time of day was 10 a.m. when the eLock 

was initialized.
Therefore, the eLock update time is 10 a.m. and 10 p.m. The 

desired update time is 6 a.m. and 6 p.m.
Using the 

RESET NET SCHED

. feature, the above steps should 

be followed at 6 a.m. or 6 p.m.

Name of last credential on LCD

The name, time, day and date of the last credential to 

successfully access the eLock appears at the bottom of the 

reader display.

Summary of Contents for Level 5 VTC eLock 200 Series













Reviews: