manualshive.com logo in svg

SMSC LAN9312, Datasheet

The SMSC LAN9312 is a highly efficient and reliable Ethernet switch designed for seamless LAN connectivity. To fully understand its features and operation, we provide a comprehensive user manual available for free download in datasheet format. Obtain your copy today from our manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface

Datasheet

SMSC LAN9312

91

Revision 1.4 (08-19-08)

DATASHEET

 

„

10M PLL (analog)

„

10M TX Driver (analog)

Auto-negotiation is started by the occurrence of any of the following events:

„

Power-On Reset (POR)

„

Hardware reset (nRST)

„

PHY Software reset (via 

Reset Control Register (RESET_CTL)

, or bit 15 of the 

Port x PHY Basic 

Control Register (PHY_BASIC_CONTROL_x)

)

„

PHY Power-down reset (

Section 7.2.9, "PHY Power-Down Modes," on page 94

)

„

PHY Link status down (bit 2 of the 

Port x PHY Basic Status Register (PHY_BASIC_STATUS_x)

 is 

cleared)

„

Setting the 

Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x)

, bit 9 high (auto-neg 

restart)

„

Digital Reset (via bit 0 of the 

Reset Control Register (RESET_CTL)

)

„

Issuing an EEPROM Loader RELOAD command (

Section 10.2.4, "EEPROM Loader," on page 149

)

Note:

Refer to 

Section 4.2, "Resets," on page 36

 for information on these and other system resets.

On detection of one of these events, the PHY begins auto-negotiation by transmitting bursts of Fast
Link Pulses (FLP). These are bursts of link pulses from the 10M TX Driver. They are shaped as Normal
Link Pulses and can pass uncorrupted down CAT-3 or CAT-5 cable. A Fast Link Pulse Burst consists
of up to 33 pulses. The 17 odd-numbered pulses, which are always present, frame the FLP burst. The
16 even-numbered pulses, which may be present or absent, contain the data word being transmitted.
Presence of a data pulse represents a “1”, while absence represents a “0”.

The data transmitted by an FLP burst is known as a “Link Code Word.” These are defined fully in IEEE
802.3 clause 28. In summary, the PHY advertises 802.3 compliance in its selector field (the first 5 bits
of the Link Code Word). It advertises its technology ability according to the bits set in the 

Port x PHY

Auto-Negotiation Advertisement Register (PHY_AN_ADV_x)

. 

There are 4 possible matches of the technology abilities. In the order of priority these are:

„

100M Full Duplex (highest priority)

„

100M Half Duplex

„

10M Full Duplex 

„

10M Half Duplex (lowest priority)

If the full capabilities of the PHY are advertised (100M, full-duplex), and if the link partner is capable
of 10M and 100M, then auto-negotiation selects 100M as the highest performance mode. If the link
partner is capable of half and full-duplex modes, then auto-negotiation selects full-duplex as the highest
performance mode.

Once a speed and duplex match has been determined, the link code words are repeated with the
acknowledge bit set. Any difference in the main content of the link code words at this time will cause
auto-negotiation to re-start. Auto-negotiation will also re-start if all of the required FLP bursts are not
received.

Writing the 

Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x)

 bits [8:5] allows

software control of the capabilities advertised by the PHY. Writing the 

Port x PHY Auto-Negotiation

Advertisement Register (PHY_AN_ADV_x)

 does not automatically re-start auto-negotiation. The 

Port

x PHY Basic Control Register (PHY_BASIC_CONTROL_x)

, bit 9 must be set before the new abilities

will be advertised. Auto-negotiation can also be disabled via software by clearing bit 12 of the 

Port x

PHY Basic Control Register (PHY_BASIC_CONTROL_x)

.

Summary of Contents for LAN9312











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LAN9312

GAIM Compact Troubleshooting preview
Compact
Brand: GAIM Pages: 2
Hama S2100 Manual preview
S2100
Brand: Hama Pages: 9
BABBITT LS8000 Owner'S Manual preview
LS8000
Brand: BABBITT Pages: 14
BABBITT LS6000 Owner'S Manual preview
LS6000
Brand: BABBITT Pages: 10
3Com OfficeConnect 5 Datasheet preview
OfficeConnect 5
Brand: 3Com Pages: 2
3Com OfficeConnect 3C1670500C User Manual preview
OfficeConnect 3C1670500C
Brand: 3Com Pages: 18
BERNSTEIN KFM Operating Instructions preview
KFM
Brand: BERNSTEIN Pages: 3
Penguin Edge RTM-ATCA-F140 Quick Start Manual preview
Edge RTM-ATCA-F140
Brand: Penguin Pages: 2
ASTEK A51606-SW Quick Start Manual preview
A51606-SW
Brand: ASTEK Pages: 3
ATEN KVMP CS1782A Quick Start Manual preview
KVMP CS1782A
Brand: ATEN Pages: 2
Magnum M9-EKCS Quick Start Manual preview
M9-EKCS
Brand: Magnum Pages: 3
Cabletron Systems Cyber SWITCH 1000 User Manual preview
Cyber SWITCH 1000
Brand: Cabletron Systems Pages: 106
PNI CT25WIFI User Manual preview
CT25WIFI
Brand: PNI Pages: 92
Unipoe 16GE+2G SFP User Manual preview
16GE+2G SFP
Brand: Unipoe Pages: 41
Xantech HD88C Installation Instructions Manual preview
HD88C
Brand: Xantech Pages: 12
Whelen Engineering Company PCCS9LW Installation Manual preview
PCCS9LW
Brand: Whelen Engineering Company Pages: 5
Tvone 1T-MX-3344 Instruction Manual preview
1T-MX-3344
Brand: Tvone Pages: 11
e+p HDMS 33 Instruction Manual preview
HDMS 33
Brand: e+p Pages: 2

Brands by name

Popular brands

Load more brands