Smith & Nephew 7205354, Instructions For Use Manual

Page: 13 / 16

13
10600266 Rev. E
DYONICS™ Handpieces Instructions for Use
Service
Cleaning Verification
1. After cleaning, inspect devices under normal lighting
to ensure that all visible soil has been removed.
2. If not visibly clean, repeat cleaning and reinspect.
3. For difficult-to-view areas, 3% hydrogen peroxide
may be applied (bubbling is evidence of the
presence of blood).
Note: Rinse instruments thoroughly with warm tap
water following any hydrogen peroxide testing.
Storage
Medical devices that will be stored between cleaning
and sterilization should be dried with a low-linting,
non-abrasive soft cloth to prevent microbial
contamination that could result from wet instruments.
Devices should ALWAYS be thoroughly cleaned prior
to storage.
Sterilization Parameters
DYONICS™ Handpieces must be sterilized by steam,
using one of the following methods only:
High Temperature Prevac Steam:
Steam,
pre-vacuum, at 270°–275° F (132°–135° C)
for 4 minutes.
High Temperature Gravity Steam: Steam,
gravity method, at 270°–275° F (132°–135° C)
for 10 minutes.
World Health Organization (WHO) Steam Cycle:
Steam, 273°–280° F (134°–138° C) for 18 minutes.
CAUTION: Do not cool the handpiece by immersing it in
cold water.
CAUTION: To prevent damage to the control unit
connector ports, do not plug in wet. Ensure that cleaned
or sterilized cable connectors are completely dry prior
to connecting to the control unit.
Service
Repairs and adjustments are to be performed only
by Smith & Nephew authorized service centers.
If service becomes necessary, call Smith & Nephew
Customer Service prior to returning the device and
request a Return Authorization (RA) number. Customer
Service can also explain the available Service
Replacement and Repair Programs.
Service items should be carefully disinfected and
packaged and returned postpaid to Smith & Nephew.
Smith & Nephew Customer Service can provide
additional instructions.
Product returned that has been serviced by an
unauthorized third party repair shop and/or sterilized
with a sterilization method other than one approved
by Smith & Nephew and/or damaged by contact with
other mechanical devices (such as shavers) may incur
additional costs, regardless of warranty status.
It is not necessary to include accessory items (i.e.,
power cords, etc.) when returning a device for service.
There are no user-serviceable components,
adjustments, or repairs other than those specifically
described in this manual.
Handpiece Cable Replacements
The following are replacement parts for the
DYONICS™ Handpieces:
REF Description
7208207 Shaver handpiece cable
7209071 Ultralight Motor Drive cable
7208208 Mini Motor Drive cable
The handpiece cable replacement is supplied in a
kit with a set of installation instructions. A standard
adjustable wrench and alcohol wipes will be required to
clean the connector pins.
Note: The Smith & Nephew DYONICS POWERMAX™,
POWERMAX ELITE Handpieces (REF 7209891,
REF 72200616, REF 72200617, and REF 7210542) and
DYONICS POWERMINI™ (REF 7221500 and REF 7221503)
do not have field-replaceable cables, and must be
returned to Smith & Nephew for cable replacement.
To replace the handpiece cable:
1. Using a standard adjustable wrench, loosen the
stainless steel locking nut at the proximal end of
the handpiece. Remove the nut from the old cable.
2. Ensure that the REF number on the replacement
cable is identical to the REF number on the old cable.
3. Clean and dry the connector pins and baseplate
of the handpiece.
4. Carefully align the pins to the sockets on the
replacement cable and join the two pieces.
5. Tighten the locking nut securely to ensure a good
electrical ground connection.
6. Connect the handpiece to the control unit and
verify operation of the handpiece using the new
power cable.
Note: The Mini Motor Drive cable and the Ultralight
Motor Drive cable are very similar. The threads on the
locking nut are different for each type of cable. If cable
replacement is difficult, recheck the REF number to
ensure it is the correct cable.