background image

12

10600266 Rev. E

DYONICS™ Handpieces     

Instructions for Use

Cleaning and Sterilizing

Cleaning

CAUTION: Dried blood, saline, and other deposits 

inside the handpieces are a major cause of equipment 

malfunction.
CAUTION: Do not use an ultrasonic cleaner or any other 

automated sterilizing or cleaning equipment. 
1.  Dispose of the blade(s) used during the operation 

following standard procedures for disposal of 

biohazardous waste. 

 

WARNING: Only Smith & Nephew DYONICS™ 

Disposable Endoscopic Blades can be used with 

the DYONICS POWER Shaver System or the DYONICS 

POWER II Control System . The blades are intended for 

single use only . Do not resterilize . Do not lubricate 

blades . Discard all blades after use .

2.  Disconnect the handpiece cable from the front panel 

by pulling back the locking collar on the connector, 

then unplugging it from the control unit. Do not 

disconnect the cable from the handpiece.

3.  Place the protective cap on the connector end  

of the cable. 

4.  Set the suction control lever to the fully open position.
5.  Rinse thoroughly with warm tap water for a minimum 

of two minutes, making sure to irrigate all features of 

the device.

6.  Immerse the handpiece and soak for a minimum of 

five minutes using a neutral pH enzymatic detergent.

7.  After immersion of the device into the enzymatic 

cleaner, agitate the device to ensure all of the air is 

removed from the device lumen.

8.  While the unit is immersed, clean using the specified 

brushes from Brushes Corp. (or equivalent) in Table 3.
–  With the suction control lever in the open position, 

insert the lumen brush in the device spigot 

(proximal end of the device) and clean the lumen 

using twisting and in/out movements of the brush 

for a minimum of 30 seconds.

–  Reinsert the lumen brush from the distal end of 

the device end and clean the lumen from the 

opposite direction using twisting and in/out 

movements of the brush for a minimum of  

30 seconds.

–  Using the blade port brush clean the nose cavity 

using twisting and in/out movements for a 

minimum of 30 seconds.

–  Using the fork area brush clean the drive fork area 

for a minimum of 30 seconds.

Table 3 . Brush Identification

Handpiece REF

Lumen  

Brush

Blade Port 

Brush

Fork Area  

Brush

7205354, 7205355, 7205971, 
7209891, 7210542, 7210586, 
72200616, 72200617, 
72200872, 72202546

Brush 1

Brush 2

Brush 3

7205357, 72201500, 72201503

Brush 4

Brush 5

Brush 3

Brush 1

Bristles: Nylon, 3.5" area length, 0.35" diameter (no taper) 
Brushes Corp. PN 86-0516-1212, or equivalent*

Brush 2 

Bristles: Nylon, 2.25" area length, 0.75" diameter (tapered to 0.60") 
Brushes Corp. PN 86-1234-0006, or equivalent*

Brush 3 

Bristles: Nylon, 0.75" area length, 0.5" diameter (no taper) 
Brushes Corp. PN 99-9986-9999, or equivalent*

Brush 4 

Bristles: Nylon, 1.25" area length, 0.28" diameter (no taper) 
Brushes Corp. PN 86-00004-0009, or equivalent*

Brush 5 

Bristles: Nylon, 1.55" area length, 0.5" diameter (tapered to 0.35") 
Brushes Corp. PN 86-0212-1234, or equivalent*

* Equivalent must include bristle material, bristle area length, and   
  bristle diameter as specified.

9.  Scrub crevices and around hinged/mating surfaces 

with the blade port brush.

10. Rinse thoroughly with warm tap water for a minimum 

of 30 seconds, making sure to irrigate all features 

of the device. Ensure that the suction control lever 

is opened and closed repeatedly while rinsing the 

device lumen.

Cleaning and Sterilizing

Summary of Contents for 7205354

















Reviews: