Smeg PVA140 Manual Download Page 2

 

Instructions for safety and use 

 

 

20 

1.

 

Instructions for safety and use 

 

 

 

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND 
IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE YOU TO 
READ THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN CAREFULLY BEFORE USING THE 
HOB. THE SERIES OF NOZZLES PROVIDED MUST ALSO BE KEPT. INSTALLATION MUST BE 
CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE.  
THIS APPLIANCE IS INTENDED FOR DOMESTIC USE AND CONFORMS TO THE 

EC DIRECTIVES

 

CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING 
FUNCTIONS: 

COOKING AND HEATING UP FOOD

; ALL OTHER USES ARE CONSIDERED 

UNSUITABLE. 

THE MANUFACTURER CANNOT BE HELD LIABLE FOR USES OTHER THAN THOSE INDICATED

 

 

 

DO NOT LEAVE WASTE PACKAGING UNATTENDED IN THE HOME ENVIRONMENT. SEPARATE THE 
VARIOUS WASTE PACKAGING MATERIALS AND CONSIGN THEM TO THE NEAREST 
DIFFERENTIATED COLLECTION CENTRE. 
 

 

 

 

 

THE APPLIANCE MUST BE EARTHED IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY 
REGULATIONS. 
 
 
 

 

THE PLUG TO BE CONNECTED TO THE SUPPLY CABLE AND THE RELEVANT SOCKET MUST BE OF 
THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE.  
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE IS INSTALLED. 

NEVER UNPLUG BY PULLING ON THE CABLE

 

 

 

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A BRIEF TEST OF THE HOB, FOLLOWING THE 
INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE 
POWER SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. 

NEVER ATTEMPT TO REPAIR THE APPLIANCE

 

 

 

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE "ZERO" (OFF) POSITION WHEN YOU 
FINISH USING THE HOB. 

 

NEVER PLACE 

PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE 

HOB RACKS. 
 

 

 
 

 

NEVER USE

 PANS OR GRIDDLES WHICH EXTEND BEYOND THE EXTERNAL PERIMETER OF THE 

HOB. 
 
 

 

 

 

 

THE IDENTIFICATION PLATE SHOWING THE TECHNICAL DATA, SERIAL NUMBER AND BRAND IS 
LOCATED IN A VISIBLE POSITION BELOW THE CASING, ATTACHED TO THIS MANUAL AND 
REPLICATED ON THE QUALITY CERTIFICATE.  

THE PLATE ON THE CASING MUST NOT BE REMOVED

 

 

 

THE APPLIANCE IS INTENDED FOR USE BY ADULTS

. KEEP CHILDREN AT A SAFE DISTANCE AND 

NEVER ALLOW THEM TO PLAY WITH IT. 
 
 
 

 

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE 
ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). 
THIS DIRECTIVE DEFINES THE STANDARDS FOR THE COLLECTION AND RECYCLING OF WASTE 
ELECTRICAL AND ELECTRONIC EQUIPMENT APPLICABLE THROUGHOUT THE EUROPEAN UNION.

 

 

The manufacturer cannot be held liable for damage to persons or things caused by failure to 

observe the above instructions, by interference with any part of the appliance or by the use of 
non-original spare parts. 

Summary of Contents for PVA140

















Reviews: