Smeg KSMD910X, Instruction On Mounting And Use Manual

Page: 16 / 56

16
Maintenance
Prior to any maintenance operation ensure that the cooker
hood is disconnected from the power supply.
Cleaning: The cooker hood should be cleaned regularly
internally and externally.
For cleaning use a cloth moistened with denatured alcohol
or neutral liquid detergents. Avoid abrasive detergents.
Warning: Failure to carry out the basic standards of the
cleaning of the cooker hood and replacement of the filters
may cause fire risks.
Therefore we recommend observing these instructions.
Grease filter
This must be cleaned once a month (and, for the model with
electronic control panel, every time LED 4 starts to flash –
see preceding page) using non aggressive detergents,
either by hand or in the dishwasher, which must be set to
a low temperature and a short cycle. When washed in a
dishwasher, the grease filter may discolour slightly, but this
does not affect its filtering capacity. To remove the grease
filter, pull the spring release handle (f) - (Fig. 2).
Charcoal filter (filter version only)
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months
(when using the hood 2,5 hours per day, in average and,
for the model with electronic control panel, every time LED
5 starts to flash – see preceding page) using hot water and
a suitable detergent, or in a dishwasher at 65°C (if the
dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put
it in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs ( g ) 90°
that affix the chimney to the cooker hood (Fig. 3) .
Insert the pad (i) of activated carbon into the frame (h) and
fit the whole back into its housing (j) .
Replacing lamps
Warning!
Prior to touching the light bulbs ensure they are cooled down.
For models shown in Fig. 1E + Fig. 4E:
1. Press on the lamp cover and release to open.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1N/O + Fig. 4N/O:
1. Unscrew the lamp cover.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Refit the lamp cover.
For models shown in Fig.1+Fig.4 (A/B/C/D/F/H/I/K/P/
Q):
1. Extract the lamp cover by levering it off with a small
screwdriver or similar tool.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1J + Fig. 4J:
1. Use a small screwdriver as a lever on the borders of
the lamp in order to remove the lightbulb.
2. Unthread the connector „a“ .
3. Slide out the lightbulb to be replaced and replace with a
new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD
LINE code 425409.
4. Carry out the replacement and mount the new lightbulb
by following instructions in the reverse.
For models shown in Fig. 1G + Fig. 5G:
Dismount the chimneys: remove the two screws ( 20 a )
that attaches the upper chimney to the support „G“ (Fig.
16) .
Remove the box „q“ : remove the screw „r“ that
secures the cooker hood.
Remove the lamp housing „s“ : remove the screws „t“
that position the housing in the lamp housing area.
Extract the damaged lamp.
Use only PHILIPS type 14515 (GX 5.3) 12V - 75W
halogen bulbs..
Reposition and secure the lamp housing „s“ and the box
„q“ and remount the chimneys.
For models shown in Fig. 1K + Fig. 4K:
Certain versions of this cooker hood provide for an
incandescent lamp at 40W maximum (E14), remove the
grease filter to access the lamp housing and carry out any
replacements.
Only for the illustrated model in Fig. 1L + Fig. 6L :
1. Open the front panel “ v ” upwards, which holds the lamp
in place, ensuring to hold the lamp “ z ” with one hand.
2. Replace the damaged lamp with one of identical technical
characteristics.
Attention! To guarantee the equivalent quality of
lighting, it is recommended to use the same type of lamp
bulb:
Philips neon Lamp bulb 13W Code Ref. 8711500644305.
Ensure that the transparent part of the lamp bulb is facing
inwards so as to guarantee correct light distribution.
3. Replacing the starter:
Use a starter with identical technical characteristics.
Recommended starter: Use a Philips S10 starter.
4. Remount the lamp housing and the front panel in the
inverse in relation to the dismounting.
Only for the models illustrated in Fig. 1M + Fig. 7M:
1. Remove the grease filters.
2. Remove the ceiling light unscrewing the 3 screws that
fix it to the hood (hold the ceiling light to prevent it falling).
3. Change the damaged bulb with one with identical
technical characteristics.
Changing the starter
Use a starter with identical technical characteristics.
Starter advised: use a Phillips S10 starter.
4. Remount the ceiling light and the grease filters in the
reverse manner to the montage.
If the lights do not work, make sure that the lamps are
fitted properly into their housings before you call for
technical assistance.
Caution
This appliance is designed to be operated by adults. Children
should not be allowed to tamper with the controls or play with
the appliance.
Do not use the cooker hood where the grill is not correctly
fixed! The suctioned air must not be conveyed in the same
channel used for fumes discharged by appliances powered
by other than electricity. The environment must always be
adequately aerated when the cooker hood and other
appliances powered by other than electricity are used at the
same time. Flambé cooking with a cooker hood is
prohibited. The use of a free flame is damaging to the filters
and may cause fire accidents, therefore free flame cooking
must be avoided. Frying of foods must be kept under close
control in order to avoid overheated oil catching fire. Carry
out fumes discharging in accordance with the regulations in
force by local laws for safety and technical restrictions.