Smeg B-One User Manual Download Page 6

Page: 6 / 52

Revision n.1

User Manual B-One

Edition: 04/2009

Page 6 of 52

INDEX

PROPER USE .............................................................................................. 9

TECHNICAL FEATURES........................................................................... 10

INSTALLATION.......................................................................................... 12

3.1

INSTALLATION AND ELECTRICAL CONNECTION............................ 12

3.2

SAFETY WARNINGS ........................................................................... 13

PRESENTATION........................................................................................ 14

4.1

FRONT DEVICES – CONTROL PANEL............................................... 14

4.2

FRONT HYDRAULIC CONNECTIONS ................................................ 14

4.3

DEVICES ON THE REAR PANEL ........................................................ 15

MACHINE OPERATION............................................................................. 16

5.1

GENERAL USER INTERFACE............................................................. 16

5.2

TURN-ON ............................................................................................. 17

5.3

STERILIZATION CYCLE SELECTION AND START-UP...................... 17

5.4

AVAILABLE CYCLES – STERILIZATION AND TESTS........................ 19

5.5

PREHEATING....................................................................................... 20

5.6

SHUTDOWN......................................................................................... 21

5.7

RECOVERY AFTER A SUDDEN BLACK-OUT .................................... 21

5.8

TANK MANAGEMENT.......................................................................... 21

5.8.1

LOADING TANK FILLING - DEMI................................................... 22

5.8.2

DEMINERALISED WATER QUALITY CONTROL .......................... 24

5.8.3

SUPPLY WATER QUALITY............................................................ 24

5.8.4

MANUAL DRAINING OF LOADING TANK WATER ....................... 25

5.8.5

WATER SUPPLY TANK DRAINING............................................... 25

5.8.6

AUTOMATIC DRAINING ................................................................ 26

5.8.7

WATER PURIFIER WATER SUPPLY ............................................ 26

5.8.8

AUTOMATIC SUPPLY FROM AN EXTERNAL CAN...................... 27

5.9

DOOR CLOSING .................................................................................. 27

5.10

CYCLE INTERRUPTION ................................................................... 28

5.11

CYCLE COMPLETED........................................................................ 29

5.12

PRINTER CONNECTION .................................................................. 29

5.13

FORCED INTERRUPTION ................................................................ 30

5.14

USER RECOGNITION....................................................................... 31

5.15

PASSWORD ENTRY PROCEDURE ................................................. 31

SERVICE MENU - SETTINGS ................................................................... 32

6.1

CYCLES ARCHIVE - INTERNAL AND MEMORY CARD ..................... 32

6.2

PREHEATING - WAKE ......................................................................... 34

6.3

LANGUAGE .......................................................................................... 34

6.4

DATE AND TIME .................................................................................. 34

6.5

DATE AND TIME FORMAT .................................................................. 35

6.6

PASSWORD ......................................................................................... 35

6.7

DISPLAY............................................................................................... 36

6.8

SD MEMORY........................................................................................ 36

6.9

PRODUCT INFO................................................................................... 36

6.10

MAINTENANCE................................................................................. 36

6.11

SERVICE ........................................................................................... 36

Summary of Contents for B-One





















































Search results

Summary of Contents for B-One

Reviews:

Brands by name

Popular brands

Smeg B-One, User Manual

Search results

Summary of Contents for B-One

Reviews:

Brands by name

Popular brands