manualshive.com logo in svg

Smeg B-One, User Manual

Share
Download
Smeg B-One User Manual Download Page 41

 
 

Revision n.1 

User Manual B-One 

Edition: 04/2009 

Page 41 of 52 

 

8  ERRORS AND ALARMS 

The machine keeps control of alarm conditions during operation.   
 
In the event that any irregularities are verified, the machine emits an acoustic signal and 
the user is informed of the error / alarm type by means of the display and the colour of the 
knob ring.   
 
Always note down any errors / alarms signalled. 
 
Some alarms are "not serious" and can be resolved by simply pressing the selector knob. 
Sometimes the machine must be switched off and then back on to allow for an electronic 
reset. 
 
Machine  overheating,  due  to  an  improper  positioning  which  does  not  allow  for  the 
necessary  cooling  of  sensitive  components,  can  cause  transient  malfunctions.  In  these 
cases, it may be necessary to switch off the machine and then allow it to cool down before 
restarting operations.   
To  ensure  maximised  autoclave  operations  and  preserve  its  components  over  time, 
spaces recommended for positioning must be respected.  
 
The  alarm  is  presented  on  the  display  as  a  "phrase"  expressed  by  3  groups  of 
alphanumeric characters, as with the following screen: 
 

a.  FIRST GROUP = identification of seriousness 
b.  SECOND GROUP = alarm type 
c.  THIRD  GROUP  =  indication  of  the  programme  phase  during  which 
alarm was set off  

 
 
For example, the message E1-32-015 on the display is to be considered:  
 

a.  FIRST GROUP = E1 
b.  SECOND GROUP = 32 
c.  THIRD GROUP = 015 

 
 
Consult the following tables to identify error descriptions from messages. 
 
 
When an alarm is set off, proceed as follows: 

1.  Take  note  of  the  alarm  and  conditions  on  the  corresponding  manual  table. 
Read the alarm description and possible causes in the following tables.  

2.  Press  the  knob  to  resolve  less  serious  errors  /  alarms  related  to  electronic 
system checks of parameters which have been stabilised 

3.  If  the  error  persists:    switch  off  the  machine,  wait  a  few  seconds,  switch  it 
back on to resolve problems involving an electronic system reset 

Summary of Contents for B-One





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands