background image

SMC Smoke Detector Guide 

 

 Copyright 

©

2011 SMC Networks

  

Page 10 

 

All Rights Reserved 

 

I/M SMCSMXX-Z rev. 2.0 

7/26/11 

If this equipment does cause harmful interference to 
radio or television reception, which can be 
determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference 
by one of the following measures: 

¾

 

Reorient or relocate the receiving antenna. 

¾

 

Increase the separation between the equipment 
and receiver. 

¾

 

Connect the equipment into an outlet on a circuit 
different from that to which the receiver is 
connected. 

Consult the dealer or an experienced radio/TV 
technician for help. 

FCC Caution: Any changes or modifications not 
expressly approved by the party responsible for 
compliance could void the user's authority to operate 
this equipment. 

This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, 
and (2) this device must accept any interference 
received, including interference that may cause 
undesired operation. 

Industry Canada Statement 

This device complies with RSS-210 of the Industry 
Canada Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful 
interference, and (2) this device must accept any 
interference received, including interference that 
may cause undesired operation. 

Ce dispositif est conforme à la norme CNR-210 
d'Industrie Canada applicable aux appareils radio 
exempts de licence. Son fonctionnement est sujet aux 

deux conditions suivantes: (1) le dispositif ne doit pas 
produire de brouillage préjudiciable, et (2) ce 
dispositif doit accepter tout brouillage reçu, y 
compris un brouillage susceptible de provoquer un 
fonctionnement indésirable. 

IMPORTANT NOTE: 
Radiation Exposure Statement: 

The product complies with the US/Canada portable 
RF exposure limit set forth for an uncontrolled 
environment and are safe for intended operation as 
described in this manual. The further RF exposure 
reduction can be achieved if the product can be kept 
as far as possible from the user body or set the device 
to lower output power if such function is available. 

NOTE IMPORTANTE: (Pour l'utilisation des appareils 
portables) : 
Déclaration d'exposition aux radiations: 

Le produit est conforme aux limites d'exposition pour 
les appareils portables RF pour les Etats-Unis et le 
Canada établies pour un environnement non contrôlé. 

Le produit est sûr pour un fonctionnement tel que 
décrit dans ce manuel. La réduction aux expositions 
RF peut être augmentée si l'appareil peut être 
conservé aussi loin que possible du corps de 
l'utilisateur ou que le dispositif est réglé sur la 
puissance de sortie la plus faible si une telle fonction 
est disponible. 

This transmitter module is authorized only for use in 
devices where the antenna may be installed such that 
20 cm may be maintained between the antenna and 

users. 

Ce module émetteur est autorisé uniquement 
pour une utilisation dans un dispositif où 

l'antenne peut être installée de telle sorte 
qu'une distance de 20cm peut être maintenue 

entre l'antenne et les utilisateurs. 

Summary of Contents for SMCSM01-Z










Reviews: