background image

                  THIS IS A HIGH PERFORMANCE PRODUCT USE AT YOUR OWN RISK

                                          This product is intended for OFF ROAD USE ONLY 
                                        This product is not intended to be used to break the law

Do not use this product until you have read the following agreement.
This agreement sets forth the terms and conditions for the use of this product.
The installation of this product indicates that the buyer has read and understands this agreement and accepts the 
terms and conditions.

DISCLAIMER OF LIABILITY

MADS, its distributors, jobbers and dealers ( hereafter Seller ) shall be in no way responsible for the product’s proper uses 
and service.  THE BUYER HEREBY WAIVES ALL LIABILITY CLAIMS.

The buyer acknowledges that he is not relying on the Sellers skill or judgement to select of furnish goods suitable for any 
particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the buyer 
hereby   waivers   all   remedies   or   liabilities   expressed   or   implied,   arising   by   law   or   otherwise   (   including   without   any 
obligation of the seller with respect fitness, merchantability and consequential damages ) whatever or not occasioned by 
the sellers negligence. 

The Seller disclaims any warranty and expressly disclaims any liability for personal injury and damages.  The 
buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this 
agreement and the buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related 
to the item of the equipment purchased.  Under no circumstances will the seller be liable for any damages or 
expenses by reason of use or sale of any such equipment.

The Seller assumes no liability regarding the improper installation or misapplication of its products.
It is the installer's responsibility to check for proper installation and in doubt contact the manufacturer.

The buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

MADS ( Hereafter Seller ) gives Limited Warranty as to description, quality, merchantability, and fitness for any particular 
purpose,   productiveness,   or   any   other   matter   of   the   Seller’s   product   sold   herewith.     The   Seller   shall   be   in   no   way 
responsible for the products  proper use and  service  and  the buyer hereby waives all rights other than those expressly 
written herein. This warranty shall not be extended, altered or varied except to be a written instrument signed by Seller and 
Buyer.

The warranty is limited to one ( 1 ) year from the date of sale and limited solely to the parts contained within the products 
kit.  All products that are in question of warranty must be returned prepaid to the Seller and must be accompanied by a 
dated proof of purchase receipt.  All Warranty claims are subject to approval by MADS.

Under no circumstances will the Seller be liable for any labor charged or travel time incurred by in 
diagnosis for defects, removal, or reinstallation of this product or any other contingent expenses.

Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any 
such equipment.

In   the   event   that   the   buyer   does   not   agree   with   this   agreement:   THE   BUYER   MAY   PROMPTLY   RETURN   THIS 
PRODUCT, IN A NEW AND UNUSED CONDITION, WITH A DATED PROOF OF PURCHASE TO THE PLACE OF 
PURCHASE WITHIN TEN (10) DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND.  

THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND 
UNDERSTANDS THIS AGREEMENT AND ACCEPTS THE TERMS AND CONDITIONS.

Page 2 of 16

Summary of Contents for SSR S06-SSR

















Reviews: