background image

7

Testing & Commissioning

100 watt/150 watt/200 watt

Warranty Validation

To validate your lifetime online warranty registration you must perform the insulation resistance 
test, the heating cable resistance test and the sensor resistance test three times during the 
installation process.

1.  Before you lay the SmartMat.
2.  After you have laid your SmartMat and before you cover your SmartMat.
3.  After your finished floor has been laid.

This information must then be recorded on your commissioning record form (enclosed in the mat box).

Heating Cable Resistance Test

This test is carried out to prove continuity of the 
heating element. A low resistance ohm meter 
should be used (ie Multimeter on ohm setting), 
connect your meter on to the brown and blue mains 
lead and confirm resistance value matches that 
quoted on your specification label on the cable cold 
lead joint.

Floor Cable Resistance Test

See 

Heating Cable Resistance Test

 and repeat with 

floor sensor cable.

Insulation Resistance Test

This test is performed to measure the insulation 
resistance between conductors and ensures the 
cable insulation is not damaged. A low resistance 
reading indicates a damaged cable and must be 
repaired or replaced.

The insulation resistance tester should be connected 
between the conductors (blue and brown cables) 
and the earth (yellow/green cable). The meter 
should record a high resistance value e.g. above 100 
Meg ohms.

Summary of Contents for Mat 100W













Reviews: