smart-e 4K-8x8-L User Manual Download Page 24 | Manualshive

Page: 24 / 61

background image

4K-8x8-L USER MANUAL V1.0

© 2018 Smart-e (UK) Ltd

www.smart-e.co.uk

PAGE | 24

10.2.2

READ EDID FROM HDBASET OUTPUTS

This function enables the 4K-8x8-L to read EDID values from screens attached to the HDBaseT outputs of the
unit to the HDMI inputs. Press and hold the F1 button on the front of the 4K-8x8-L, then press input button 3.
The LCD will update to show EDID HDBaseT mode is selected, press the OK button on the front of the 4K-8x8-
L to confirm.

The LCD will update to ready to accept command as shown below.

«
...
22
23
24
25
26
...
»

Summary of Contents for 4K-8x8-L






























































Reviews:

No comments

Related manuals for 4K-8x8-L

Underwater Switch 24V DC/DMX/02

Brand: Oase Pages: 40

Brand: Grizzly Pages: 2

Edison Cooper Power Series

Brand: Eaton Pages: 12

Brand: NETGEAR Pages: 2

SmartSTACK 100 ELS100-16TX

Brand: Cabletron Systems Pages: 16

Brand: Lantech Pages: 29

Brand: TRENDnet Pages: 2

Brand: National Instruments Pages: 12

Brand: Comm-Tec Pages: 10

Brand: SMART-AVI Pages: 2

Brand: AT&T Pages: 24

Brand: Wyrestorm Pages: 2

DOMINION KX II DKX2-0E-E

Brand: Raritan Pages: 257

Moeller IZM Series

Brand: Eaton Pages: 4

Brand: CYP Pages: 24

Brand: AEB Pages: 10

MARINCO PRO INSTALLER 771-SFD

Brand: BEP Pages: 4

Brand: SolidView Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands