SMA sunny boy 2000hf-us Installation Manual Download Page 66

Page: 66 / 112

Opening and closing

SMA America, LLC

SB20_25_30HFUS-eng-IUS113711

Installation Guide

8.2 Open SMA DC Disconnect

1. Turn and loosen the screws on the enclosure of the

SMA DC-Disconnect in a counterclockwise
direction.

2. Remove the lid to the front.
3. Lay the lid to one side in such a way that it will not

become damaged.

☑ The SMA DC-Disconnect is open.

DANGER

High voltages inside the SMA DC-Disconnect. Death or serious injuries.
After opening the SMA DC-Disconnect there are still high voltages inside the
SMA DC-Disconnect at the DC contacts of the DC terminal block and at the contacts of the
DC switch.

• Do not touch contacts at the DC terminal block and on the DC switch.

Summary of Contents for sunny boy 2000hf-us

















































































































Search results

Summary of Contents for sunny boy 2000hf-us

Reviews:

Related manuals for sunny boy 2000hf-us

Brands by name

Popular brands

SMA sunny boy 2000hf-us, Installation Manual

Search results

Summary of Contents for sunny boy 2000hf-us

Reviews:

Related manuals for sunny boy 2000hf-us

Brands by name

Popular brands