background image

2

2933

4

2019

-

SH 240 & SH 320

DECLARATION OF CONFORMITY

Sleipner Motor AS

P.O. Box 519, Arne Svendsensgt. 6-8

N-1612 Fredrikstad, Norway 

Declare that this product with accompanying standard control systems complies with 

the essential health and safety requirements according to:

DIRECTIVE 2013/53/EU

DIRECTIVE 2014/30/EU

DIRECTIVE 2014/35/EU

MC_0020

Installation Instructions

Planning Considerations and Precautions................................. 3

Thruster Measurements  ........................................................... 4

Thruster Specifications

 .............................................................. 5

Technical Specifications

 ............................................................ 5

Positioning of the Retract thruster  ............................................ 6

Performance Table .................................................................... 7

Technical Requirements / Hydraulic hose connections to motor   ..

................................................................................................... 7

Installation Instructions

Hydraulic Thruster Installation Considerations and Precautions   ..

................................................................................................... 8

Marking and Trimming of SRF Flange ....................................... 9

Installation Pre-check .............................................................. 10

Required Modifications After Pre-check

 .................................. 11

SRF Flange Installation ........................................................... 12

Motor House Installation .......................................................... 13

Hatch Installation ..................................................................... 14

Motor to House Installation ...................................................... 15

Hydraulic connections  ............................................................ 16

Oil Tank Installation ................................................................. 17

Control Panel Cable Installation .............................................. 18

S-link Planning & Precautions ................................................. 19

Visual Wiring Diagram ............................................................. 20

Technical Wiring Diagram ........................................................ 21

Check drive shaft alignment  ................................................... 22

Calibrate drive shaft alignment ................................................ 22

Actuator Configuration

 ............................................................. 22

LED Indication ......................................................................... 22

Control Panel Installation ........................................................ 23

Checklist for DC and IP Thrusters ....................................... 24

 

Spare Parts ............................................................................ 25

Warranty statement  .............................................................. 25

Contents

EN

MC_0113

Planning Considerations and Precautions

EN

•     If the height of the room you are installing the Side-Power is limited consider the three diff erent confi guration designs.

      - Angled 

      -Horizontal

      -Vertical

•  Do not install the thruster in a position where you need to cut a stiff ener/ stringer/ support for the hull integrity without checking with the boat builder  

  this can be done safely.

•  The motor, its components, contacts/ plugs or other joints in the control cables must be mounted so they will remain dry at all times.

•  We advise painting the thruster with primer and antifouling. 

(NB: Do not paint the anodes, sealings or propeller shafts)

•  Do not fi nish the inside of the tunnel with a layer of gelcoat/ topcoat or similar. There is only room for a thin coat of primer and two layers of anti-fouling  

  between the tunnel and the props.

•  keep installation within advised measurements. The entire surface is hard coated seawater resistant aluminium. Do not damage/penetrate the coat.

•  The oil tank is placed higher than the pumps to ensure enough gravity feed and pressure for feed ports. 

(NB: The height of oil levels in the  

  hydraulic tank should be higher than the connected hydraulic pumps.) 

•   Find a suitable location for the hydraulic tank installation for future maintenance accessibility. There must be enough space around the oil tank to  

    change fi lters, fi ll oil and inspect gauges and indicators.

It is the installers responsibility 

When installing Side-Power equipment to follow the outlined regulations/ classifi cation rules (electrical/ mechanical) according to 

international or special national regulations. Instructions in this guide cannot be guaranteed to comply with global electric/ mechanic 

regulations/ classifi cation rules.

It is the installers responsibility

To follow all health and safety laws in accordance with their local outlined regulations/ classifi cation rules. 

Before installation, it is important that the installer reads this guide to ensure necessary acquaintance with this product. 

The recommendations made in this manual are guidelines ONLY, and Sleipner Motor AS (Side-Power) strongly recommend that 

before installation, advise is obtained from a naval architect familiar with the particular vessel and regulations/ classifi cations.

    This manual is intended to support educated/ experienced staff  and is therefore not suffi  cient in all details for professional 

installation. 

(NB: These instructions are only general instruction. If you are not skilled to do this work, please contact professional 

installers for assistance.)

    All electrical work must be done by a licensed professional. 

IMPORTANT 

Faulty installation of the tunnel, thruster or panel will render all warranty given by Sleipner Motor AS void.

MC_0038

IMPORTANT 

Stern mounted retract thrusters must not be installed to confl ict with the main boat propellers or its water trail. (NB: consult a naval 

architect for an exact position.)

Summary of Contents for SIDE POWER SRH 240 TC





























Reviews: