SkyLink ATOMS Series Owner'S Manual Download Page 38

WARRANTY ON SKYLINK GARAGE DOOR OPENER

LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE
This SKYLINK brand product, as supplied and distributed by SKYLINK and delivered new, in the original 
carton to the original consumer purchaser (not transferable or assignable), is warranted by SKYLINK 
against manufacturing defects in materials or workmanship for the limited warranty period of:

WARRANTY PERIOD

Model*

Motor

Chain

Belt

Parts

Accessories

Group A

Lifetime

Lifetime

Lifetime

5 Years

1 Year

Group B

10 Years

10 Years

10 Years

3 Years

1 Year

Group C

6 Years

5 Years

5 Years

1 Year

1 Year

Refer to model numbers below for different groups. 

Group A:

 ATR-1723CK, ATR-1723CKW, ATR-1723BK, ATR-1723BKW

Group B: 

ATR-1622CK, ATR-1622CKW, ATR-1622BK, ATR-1622BKW, ATR-1722C, 

                  ATR-1722CK, ATR-1722CKW, ATR-1722B, ATR-1722BK, ATR-1722BKW

Group C:

 ATR-1611C, ATR-1611CW, ATR-1612C, ATR-1612CK, ATR-1612CKW, 

                  ATR-1612B, ATR-1612BK, ATR-1612BKW 

This limited warranty is valid only on products purchased and used in the United States / Canada that 
have been installed, operated, and maintained according to the instructions attached to or furnished with 
the product. To receive warranty service, the purchaser must contact SKYLINK at the address or phone 
number provided below for problem determination and service procedures. Purchaser will be advised 
of disassembly and shipping instructions, then send the product or component, pre-paid and insured to 
SKYLINK. Purchaser must allow SKYLINK a reasonable opportunity to inspect the product claimed to be 
defective prior to removal or alteration of its condition. The original dated bill of sale must be presented 
upon request as proof of purchase to SKYLINK to receive warranty service. 

During the applicable warranty period, a product will be repaired, replaced, or the purchase price 
refunded, at the sole option of SKYLINK. SKYLINK may use new or reconditioned parts in repairing a 
product, or replace the product with a new or reconditioned product. 

Replacement parts and products are warranted for the remaining portion of the original product’s 
warranty or ninety (90) days, whichever is longer. All replaced parts and products are the property of 
SKYLINK and you must return them to SKYLINK.

This limited warranty covers manufacturing defects in materials or workmanship encountered in 
normal residential household, non-commercial use of this product and shall not cover the following: 
damage that occurs in shipment, delivery, installation, and uses for which this product was not 
intended; damage caused by unauthorized modification or alteration of the product; product where 
the original factory serial numbers have been removed, defaced, changed in any way, or cannot 
be readily determined; cosmetic damage including scratches, dents, chips, and other damage to 
the product’s finishes; damage caused by abuse, misuse, pest infestations, accident, fire, floods, or 
other acts of nature or God; damage caused by use of equipment, utilities, services, parts, supplies, 
accessories, applications, installations, repairs, external wiring or connectors not supplied or 
authorized by SKYLINK; damage caused by incorrect electrical line current, voltage, fluctuations 
and surges; damage caused by failure to operate and maintain the product according to instructions; 
in-home instruction on how to use your product; and service to correct installation not in accordance 
with electrical codes or correction of household electrical (i.e., house wiring, fuses); and does not 
cover batteries, missing or damaged parts from clearance or open box sales. The cost of repair or 
replacement under these excluded circumstances shall be the customer’s responsibility.

EXCLUSION OF IMPLIED WARRANTIES 

IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED 
BY LAW. 

Some states and provinces do not allow limitations on how long an implied warranty lasts, so the 
above limitations or exclusions may not apply to you. This limited warranty gives you specific rights, 
and you may also have other rights, which vary from state to state and province to province. 

LIMITATION OF REMEDIES 

YOUR SOLE AND EXCLUSIVE REMEDY IS PRODUCT REPAIR, PRODUCT REPLACEMENT, OR REFUND 
OF THE PURCHASE PRICE AT SKYLINK’S OPTION, AS PROVIDED IN THIS LIMITED WARRANTY. 
SKYLINK SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, 
INCLUDING BUT NOT LIMITED TO TIME AWAY FROM WORK, HOTELS AND/OR RESTAURANT MEALS, 
REMODELING EXPENSES, LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER 
BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF 
SKYLINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states and provinces 
do not allow exclusion or limitation of incidental or consequential damages, so the above limitations 
or exclusions may not apply to you. This warranty gives you specific rights, and you may also have 
other rights, which vary from state to state and province to province. 

SKYLINK does not warrant uninterrupted or error-free operation of the product. No warranty or 
guarantee given by any other person, firm, or corporation with respect to this product shall be binding 
on SKYLINK.

To obtain warranty service, please contact SKYLINK at: 

1-800-304-1187 

[email protected] 

37

SKYLINK LIMITED WARRANTY

Summary of Contents for ATOMS Series







































Reviews: