13
SerVice anD inStallation Manual
2.10
2.10
data Logger
data Logger
The LMS includes a data logger that records all
significant events including actual sensor values and
a date and time stamp. The data logger memory can
hold over 32 000 records, this is equivalent to
several days or several years of operation
depending on the recording mode selected and
machine use. The data can be extracted using a
USB mass storage device (USB key) and then
transferred to a personal computer for analysis.
2.10a recording Modes
Adjust the data logger recording mode as required:
1. Go to menu
4)
and select
4k) D
ata
l
oGGer
.
2. Enter the user password ‘aza’ and press
enter
.
3. Use
up
and
Down
to select the data logger
recording mode and press
enter
.
4. Press
enter
to save any changes.
5. Press
exit
to return to the operation display or
press
Down
to adjust the data logger date and
time (see
Date and Time
sub-section).
recording Modes description:
alarm only
. Record alarms only. All the other
data logger modes also record alarms.
automatic recording intervals
. A record is
added at a specified interval. When the
automatic recording data logger mode is
selected on menu
4k) 1)
(see step 3 above)
select
1a) M
inuteS
, press
enter
and then use
up
and
Down
to adjust the record interval in
minutes.
automatic variation
. A record is added when
load increases by more than the operator
adjusted percentage. When the automatic
variation data logger mode is selected on menu
4k) 1)
(see step 3 above) select
1a) V
ariation
(%)
, press
enter
and then use
up
and
Down
to
adjust the variation threshold.
automatic peak
. In the automatic peak mode
the data logger analyzes the measured weight
and records the peak value only. One threshold
per load cell must be adjusted. When the weight
drops by more than the peak threshold the peak
weight is recorded. Only one event is recorded
for each pick when the threshold is adjusted
correctly. When the automatic peak data logger
mode is selected on menu
4k) 1)
(see step 3
above) select
1a) t
hreSholD
№1
, press
enter
and then use
up
and
Down
to adjust the peak
threshold for the first load cell. Press
Down
to
repeat for the second load cell etc. Up to four
load cells can be programmed for automatic
peak data logging.
User input
. The status of all sensors is
recorded on demand. A normally open push
button must be installed on a digital input to the
LMS through a pre-determined wire of the
power supply and lockout cable.
all data
. All communications between a display
and its sensors are recorded.
2.11b Date and time
Adjust the data logger date and time as required:
1. Go to menu
4)
and select
4k) D
ata
l
oGGer
.
2. Enter the user password ‘aza’ and press
enter
.
3. Select
2) D
ate
and press
enter
.
4. The digits of the year should be flashing: use
up
and
Down
to adjust the year and press
next
.
5. Use
up
and
Down
to adjust the month and
press
next
.
6. Use
up
and
Down
to adjust the day and press
enter
to confirm.
7. Select
3) t
iMe
and press
enter
to adjust the time.
8. The hour should be flashing: use
up
and
Down
to adjust the hour from 00 (midnight) to 23 (11 pm).
9. Press
next
to adjust the minute.
10.Use
up
and
Down
to adjust the minute and
press
next
.
11. Use
up
and
Down
to adjust the second and
press
enter
to save any changes.
12.Press
exit
to return to the operation display.
Note: all alerts are recorded by the data logger
regardless of the mode selected.
SkyAzul, Equipment Solutions
www.skyazul.com
301-371-6126
