background image

7

General Operation

The apron and attachment functions on the spreader are driven hydraulically by the hydraulic pump 

run by the tractor PTO. 

The spreader is equipped with a hydraulic manifold with precision hydraulic valves (Figure 4) to fine-

tune both the attachment and apron chain speed to accommodate a wide range of spread patterns, 

material density and much more. To change the settings, raise the glass cover and rotate the knobs to 

the desired position.

The metering gate in the rear can be adjusted manually from 0-13” to control the depth of material 

flowing out onto the attachment. It is adjusted by turning the end gate wheel (Figure 5) to the desired 

position and engaging the spring loaded lock pin. Turn the wheel clockwise to raise the gate and 

counter-clockwise to lower it.

Figure 4

Figure 5

Lock Pin

The  remote  floor  shut  off  switch  (Figure  5)  is 

used to temporarily stop the apron chain while 

the spinners are still rotating. This feature is 

used when the operator makes a turn or pass-

es through an area where no material is to be 

spread. 

OPERATION

Figure 6

Summary of Contents for PEQUEA SF5



















Reviews: