background image

SJE Rhombus

®                                                                                                        

     14                                                  Type IFS Operation Manual

TROUBLESHOOTING INFORMATION SCREENS

Current Panel Configuration

Duplex
Timed Dose
C-Level

 Sensor

40” Sensor

This section displays the current configuration of the controller. *The example shows a controller 
configured as a Duplex, Timed Dose using a 40” C-Level

 sensor for level sensing.

C-Level

 Status

Simulator
Frequency 

  2315 

Hz

Tank Level   

 

26.3 in

The simulator is used to verify the functionality of the controller by simulating the tank level.

This section displays the frequency of the C-Level

 sensor as measured by the controller, as well 

as the calculated tank level. The normal operating range of the C-Level

 sensor is between 1000Hz 

and 3000Hz. If the C-Level

 sensor frequency is operating significantly outside of the normal range, 

a “Sensor Fail” alarm will occur.

Float Status

Redundant High Level 

Down

Redundant Low Level 

Up

This screen displays the status of each float switch connected to the controller. *The example shows a 
controller configured as C-Level™ sensor control.

Pump Status

Pump 1 Called 

 

Off

Pump 1 Amps  

 

0.0 A

Pump 2 Called 

 

Off

Pump 2 Amps 

 

0.0 A

This screen displays the status of each pump connected to the controller. *The example shows a 
controller configured as Duplex.

Alert Status

Horn 

   Off

Beacon   Off
Alarm 

Aux 

  Off

This screen displays the status of the controller alarm.

Summary of Contents for IFS























Reviews: