sitrex SR 320/8 H Use And Maintenance Spare Parts List Download Page 12 | Manualshive

Page: 12 / 42

background image

12

Rest the main frame (2) on stands and then insert the wear bushings

(5). Insert pin (3) into

hole (A) and fasten with the spring pin (42). Position the drawbar (1) so that pin (6) can be
inserted, and fasten pin (6) with the spring pin (7).

Mount wheels (10) on the axle pins, first placing the large guard (9) and then the small
guard (11), the washer (12) and tighten with the nut (13). Mount the parking stand (14) to
the mount on the drawbar (1), and fasten with pin (15) and clip (16). The machine can now
be placed on the ground.

«
...
10
11
12
13
14
...
»

Summary of Contents for SR 320/8 H











































Reviews:

No comments

Related manuals for SR 320/8 H

Brand: Zetec Pages: 23

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: KaVo Pages: 4

ORTHOPANTOMOGRAPH OP 3D

Brand: KaVo Pages: 40

KEY Laser III 1243

Brand: KaVo Pages: 103

EXTRAmatic 9040

Brand: KaVo Pages: 56

ESTETICA E70 Vision

Brand: KaVo Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands