manualshive.com logo in svg

sitrex SR 320/8 H, Use And Maintenance Spare Parts List

Share
Download
sitrex SR 320/8 H Use And Maintenance Spare Parts List Download Page 27

27 

CARDAN SHAFT MAINTENANCE 

 
More detailed information may be found in the Cardan shaft manual, which, together with this manual, forms 
an essential part of the accident-prevention documentation. It is your responsibility to read and comply with 
this documentation. 
If information given in this manual conflicts with that given in the Cardan shaft manual, you should follow the 
instructions given by the Cardan shaft manufacturer. 
 

MAINTENANCE OF SLIDING PARTS 

 

DISMANTLING 

Turn the two eccentric pins on the ferrule until the 
protective cone comes free. 
 

Withdraw the shaft protective guard. 
 

Cheek the condition of the ferrule and all protective 
parts. 
 

ASSEMBLY 

Lubricate the supporting 
ferrule seating. 
 

Refit the supporting ferrule. 
 

Reattach the protective guard to the Cardan shaft by 
turning the eccentric pins on the supporting ferrule. 
 

Summary of Contents for SR 320/8 H











































Reviews:

No comments

Brands by name

Popular brands

Load more brands