Document NO.
：
RD-558A-39-001
2
/
5
Version: F
special smoke alarms with lights or vibrating devices to alert
occupants.
7: Smoke alarms can only sound their alarms when they detect
smoke or detect combustion particles in the air. They do not
sense heat, flame, or gas. This smoke alarm is designed to
give audible warning of a developing fire. However, many
fires are fast - burning, explosive, or intentional, and others
are caused by carelessness or safety hazards. In this circs,
Smoke may not remake the unit alarm
QUICKLY ENOUGH
to ensure safe escape.
8: Smoke alarms have limitations. This smoke alarm is not
foolproof and is not warranted to protect lives or property
from fire. Smoke alarms are not a substitute for insurance.
Homeowners and renters should insure their lives and
property. In addition, it is possible for the smoke alarm to fail
at any time. For this reason, you must test the smoke alarm
weekly and replace unit every 10 years.
Do Not Install Smoke Alarms in
the Following Places:
1: Near appliances or areas where normal combustion
Regularly occurs (kitchens, near furnaces, hot water heaters).
Use specialized smoke alarm with unwanted alarm control for
this areas.
2: In areas with high humidity, like bathrooms or areas near
dishwashers or washing machines. Install at least 10feet
away from these areas.
3: Near air returns or heating and cooling supply vents. Install at
least 3 feet away from these areas. The air could blow smoke
away from the detector, interrupting its alarm.
4: In rooms where temperatures may fall below
40
℉
or rise
above 100
℉
.
5: In extremely dusty, dirty, or insect
–
infested areas influence
particles interfere with smoke alarm operation.
Battery Specification:
Rating voltage: DC 1.5V
Package: AA alkaline battery
Recommend battery:
Energize: E91
Gold Peak Group: GP15ALR6
Raymax:
LR6
Replace Battery:
1: Turn the alarm body counterclockwise and take out the alarm
body from the bracket.
2: Take out the old battery from the battery box.
3: Fix the two new batteries to the battery box. Please note the
battery polarity.
4: Fix the battery into battery box, fit alarm body on bracket and
turn the alarm body clockwise.
5: Test smoke alarm using test button. The sound pattern is 3
short beeps-1.5seconds pause, repeat it. I
f there’s no sound
output, it means that the smoke alarm is faulty or the
installing operation is wrong, and you should gain the
correctly method of disposal through reading “TROUBLE
SHOOTING”
.
NOTE: During testing, because the unit send the wireless
signal, may the other smoke detector will alarm. Once
release the test button, the other smoke detector will
stop alarming in 1 minute.
LED indicator
1: When the alarm is running normally, the red LED will flash 1
time per 40 seconds.
2: When the battery failure or low battery is detected, the alarm
will “chirp”
1 time and with a corresponding red LED
flashing 1 time per 40 seconds.
3: When the unit is fault, the alarm will
“
chirp
”
1 time per 40
seconds.
4: When the unit is running in the silence mode, the red LED
will flash once every 8 seconds.
Note: When the units chirp 1 time per 40 second, Press the test
button, it will be paused for this
warning tone
for 8 hours.
It can still normally detect smoke during this period, it
only remove nuisance warning tone.
Alarm silence (silence mode)
During the unit is alarming, push the test button, it will be
paused the unit alarming for approx 10 minutes. The red LED
will flash once every 8 seconds, it indicates the smoke alarm
is running into the silence mode. Smoke alarms are designed
to minimize nuisance alarms. Combustion particles from
cooking may set off the alarm if the alarm is located close to
the cooking area. Large quantities of combustible particles are
generated from spills or when grilling/frying. Using the fan on
a range hood that vents to outside (non-recirculating type) will
also help remove these combustible particles from the kitchen.
The alarm silence (test button) is extremely useful in a kitchen
area or other areas prone to nuisance alarms.
The silence feature is to be used only when a known alarm
condition, such as smoke from cooking activates the alarm.
The smoke alarm will automatically reset after approximately
10 minutes, if after this period, particles of combustion are
still present, the alarm will sound again.
The alarm silencer (silence mode) can be repeatedly until the
air has been cleared of the condition causing the alarm.
Testing the Smoke Alarm:
Test each smoke alarm to be sure it is installed correctly and
operating properly.
