Document NO.
：
RD-558A-39-001
3
/
5
Version: F
1: Do not use an open flame to test the alarm. You may ignite
and damage the alarm or your home.
2: Test the alarms weekly and upon return from vacation or
when no one has been at home for several days.
3: Stand at an
arm’s length from the
unit when testing.
Test all smoke alarms weekly by doing the following step.
4: Firmly press the test button for at least 5 seconds. The alarm
will sound 3 short beeps
–
1.5 seconds pause, then repeat it
until release the button. The alarm may sound for up to a few
seconds after releasing the test button.
DANGER:
If the alarm sounds, and it is not being tested, it
means the unit is sensing smoke,
THE SOUND OF THE ALARM
REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.
Wireless function description:
Wireless frequency:
433MHz
Operation current
:
RF Receiver:
<5mA
RF emitter:
<10mA
Wireless distance:
>20 meters
Note: Make sure the battery is installed well before operating the
product.
1: Send wireless coding mode
a:
Press and hold the test button on the alarm until the red
LED light about 1S, release the button, the
alarm
enters
into the wireless coding sending status. The LED is
always ON. If you press the test button or have not
wireless learning signal within 30 second, the LED will be
OFF.
Note: enter this mode from standby status, press and hold
the button for about 12 seconds required.
b: When there are other alarms received in response to this
wireless coding command, the red LED flashes for about 2
seconds. Then re-enter the wireless coding sending status,
waiting for the next alarm response. If there is no alarm
response to this command within 30 seconds, the unit will
exit automatically.
2: Learning mode
a: Press the test button of the alarm, the red LED light 1
second, then release the button immediately, the alarm
enters into learning mode. Note: There must have other
alarms in the "Send Wireless coding mode", this alarm
will be able to enter into the learning mode.
b: If the learning is successful, the red LED flashes for
about 2 seconds, then exit the learning mode
automatically.
3: Clear code mode
a
: Press and hold the test button on the alarm until the red
LED flashes for about 1 second, release the button, the
alarm enters the clear code mode. Note: enter this mode
from standby mode, press and hold the button for about
16 seconds required.
b: After releasing the button, press the button when the red
LED lights up, release the button when the red LED is
off, if you hear the sound of `BI` sound after two cycles,
that indicates clear code is success, the alarm own
wireless code and the wireless code learned will be reset
to the new code, the new code is random.
4: How to match each other smoke alarm
a:
Take one alarm to enter into "send wireless coding mode".
b: Take another alarm into learning mode, when the red LED
flashes for 2 seconds, which means that the learning
success.
c: Follow steps b to complete the all alarms.
d: Press the test button, exit the
“
send wireless coding
mode
”
. The red LED is OFF. Wait for about 30 seconds.
e: Take one alarm, press the test button and hold for about 30
seconds. If other alarms all enter into the wireless alarm
status. That indicates a successful match.
Maintenance and Cleaning:
In addition to weekly testing, the alarm requires periodic
cleaning to remove dust, dirt, and debris.
Clean the alarm at least once a month to remove dust, dirt, or
debris.
Use a vacuum cleaner with the soft brush, vacuum all sides and
covers of smoke alarm. Be sure all the vents are free of debris.
IMPORTANT: Do not attempt to remove the cover to clean
inside. This will affect warranty.
WARNING! Use only the batteries specified. Use different
batteries may have detrimental effects on the alarm. A good
safety measure is to replace the battery at least once a year.
Note: Reinstall immediately after cleaning and then test unit
using the test button.
Repair:
Caution: Do not attempt to repair the alarm. It will affect your
warranty.
If the alarm is not operating properly, and is still under warranty,
return it to the original place you buy. Pack it in a well-padded
carton, and ship to the original place you buy.
If the alarm is no longer under warranty, have a licensed
electrician replace it immediately with a comparable alarm.
Practice Fire Safety:
If the alarm sounds, and you have not pushed the test button, it is
warning of a dangerous situation, your immediate response is
necessary. To prepare for such occurrences, develop family
escape plans, discuss them with all household members, and
practice them regularly.
