Siser TS DUE Instructions Manual Download Page 8

  

 

 

This manual is the property of SISER S.r.l., any even partial reproduction is forbidden  

Mod. PRD 22 rev.2   -   last updating: 01/2015 

 

6. Mounting, Transport and Mounting Location 

The installation of the transfer press must only be performed by suitably qualified personnel, as the electrical 

connections must comply with local regulations.  

Before mounting the transfer press prepare a suitable mounting location. Handle the package containing the 

transfer press with care and with the aid of suitable tools. As the transfer press is heavy, the mounting should 

be performed by two people. 

For the mounting location you need a stable table with a height of approximately 70 cm. Fixing the unit's feet 

to the table top is a good way to increase the safety of the unit particularly if the work table is mobile.  

7. Electrical Connection 

The transfer press must be mounted in a room featuring a power supply system approved by local authorities 

and complying with effective safety regulations for electric devices.  

The available power supply lines must have a cross section sufficient for the transfer press's energy demand 

of 2 kW, preferably in its own power circuit. The characteristic values of the power supply system must comply 

with the characteristics of the heat transfer press. Please check the values stated on the label. 

The  coloured  conductor  markings must  be  carefully  complied  with and  the  transfer  press must  be  earthed. 

Please refer to EN 60439 

– 1 (CEI 17-13/1). 

The power socket must have an electric protective earthing and a residual-current-operated protective device 

(RCD) disconnecting the circuit if the residual current exceeds 30 mA. 

Do not use cables with damaged insulation. It is inadvisable to use extension cords.  

Remove the plug from the power socket before starting any maintenance or repair work, in particular 

if it is necessary to open the box of the control panel or to perform work on the heating elements. 

The graphic symbol „High-Tension“ signalises a serious danger and is attached on the box of the control panel 

and  on  top  of  the  heating  elements.  Switch  off  the  master  switch  before  exchanging  or  removing  heating 

elements.  

 

8. Directions for Use 

Please  note  the  risks  involved  in  using  a  transfer  press  mentioned  in  paragraph  4  of  this  manual,  in 

particular 

 

the risk of squashing your hands in between the plates 

 

the risk of an electric shock 

 

the risk of burning your hands and arms on the heating plates 

Wear protective gloves to avoid the risk of getting burned.  
 
 

Summary of Contents for TS DUE


















Reviews: