background image

18 

18

  EXPLODED DIAGRAM 

Note: 

Always make sure the mains supply is of the correct voltage and the 

correct  fuse  protection  is  used.  In  the  event  of  replacing  the  fuse  always 
replace the fuse with the same value as the original.

 

 

Note: 

If  an  extension  lead  is  required  in  order  to  reach  the  mains  supply; 

ensure that this too is rated for the correct voltage and fuse rating. 
 
 

 

Note: 

The cross section of the extension lead should be checked so that it 

is of sufficient size so as to reduce the chances of voltage drops.

 

Warning: 

Never connect live or neutral wires to the earth terminal of the 

plug. Only fit an approved plug with the correct rated fuse (5 amp). If in 
doubt consult a qualified   electrician.

 

  ELECTRICAL CONNECTION….cont 

          Yellow / green 

Earth 

 

Blue   

 

Neutral 

 

Brown  

 

Live 

 
As  the  colours  of  the  wires  may  not  correspond  with  the  markings  in  your  plug,  pro-
ceed as follows: The wire which is coloured blue, must be connected to the terminal 
marked with N or coloured black. The wire which is coloured brown, must be connect-

ed to the terminal, which is marked L or coloured red. The wire which is coloured yel-
low  /  green  should  be  connected  to  the  terminal  which  is  coloured  the  same  or 
marked  

 
 

Always secure the wires in the plug terminal carefully and tight-
ly. Secure the cable in the cord grip carefully.

 

The wires for the plug are coloured in the following way:

 

Summary of Contents for 01943













Reviews: