6
ELECTRICAL CONNECTION
SAFETY INSTRUCTIONS….cont
CAUTION:
The warnings and cautions mentioned in this user manual can
not cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be applied.
When using the sander always ensure the operator as well as those in the
area wear eye protection.
Sanding operations will cause dust to become airborne with the potential
to be highly toxic; always wear a face mask during these operations, as
well as ensuring the area is well ventilated. It is also highly recommended
to use a dust collector to reduce airborne particles.
When using this sander, it is advisable to ensure the operator as well as
those in the area wear ear protection, particularly during extended peri-
ods of use.
WARNING!
It is the responsibility of the owner and the operator to read, understand
and comply with the following:
You must check all electrical products, before use, to ensure that they are safe.
You must inspect power cables, plugs, sockets and any other connectors for wear or
damage.
You must ensure that the risk of electric shock is minimised by the installation of appro-
priate safety devices; A residual current circuit Breaker (RCCB) should be incorporated
in the main distribution board. We also recommend that a residual current
Device (RCD) is used. It is particularly important to use an RCD with portable products
that are plugged into a supply which is not protected by an RCCB. If in any doubt
consult a qualified electrician.
Connecting to the power supply:
This SIP sander is fitted with a standard 230v ~ 13 amp type plug. Before using the
heater, inspect the mains lead and plug to ensure that neither are damaged. If any
damage is visible have the heater inspected / repaired by a suitably qualified per-
son. If it is necessary to replace the plug a heavy duty impact resistant plug would be
preferable.
19
PARTS LIST
No.
Description
SIP Part No.
1
Sanding belt 152 x 1219 mm 60 grit
06870
Sanding belt 152 x 1219 mm 80 grit
06868
Sanding belt 152 x 1219 mm 120 grit
06270
2
Bed
WD02-00004
3
Knob
WD02-00005
4
Washer
WD02-00006
5
Bolt M4x8
WD02-00007
6
Nut M6
WD02-00008
7
Fence
WD02-00009
8
Fence support
WD02-00010
9
Lock pin for fence support
WD02-00011
10
Nut M6
WD02-00008
11
Lock washer 5 mm
WD02-00013
12
Screw M6 x 10
WD02-00014
13
Self tapping screw 4x16
WD02-00015
14
Switch housing
WD02-00016
15
No-volt release switch KJD12
WD02-00017
16
Screw 4 x 16
WD02-00015
17
Bearing cap
WD02-00018
18
Sleeve
WD02-00019
19
Pin
WD02-00020
20
Drive drum
WD02-00021
21
Rear switch housing cover
WD02-00022
22
10" Sanding disc 60 grit coarse
06860
10" Sanding disc 80 grit coarse
06861
10" Sanding disc 120 grit medium
06862
10" Sanding disc 150 grit fine
06864
23
Screw M6 x 10
WD02-00027
24
Sanding disc
WD02-00028
25
Sanding disc support
WD02-00029
26
Screw M4 x 45
WD02-00030
27
Sanding disc guard
WD02-00031
28
Sanding disc cover guard
WD02-00032
29
Hex nut M6
WD02-00008
30
Bolt M6 x 16
WD02-00034
31
Table frame bracket
WD02-00035
32
Table support
WD02-00036
33
Table
WD02-00037
34
Dust port
WD02-00038
35
Self tapping screw 4 x 20
WD02-00039
36
Clamp handle
WD02-00040
37
Carrying handle
WD02-00041
