background image

 

Revision 1.00 

 

IMPORTANT: Wraith 2.0 Warranty 

Wraith 2.0 has a limited 2-year warranty.  

Welcome to Singularity Computers and your new Wraith 2.0! We look forward to seeing what you 

create.  

 

1: The Integrated Liquid Cooling System is pressure tested at the factory, so there is no need to adjust 
the fasteners on the manifold. Take care not to over tighten any fasteners on the acrylic. As soon as 
you feel any significant feedback or tension go no more than 1/4th of a turn past it. On the metal parts 
you can tighten normally. We are not responsible for damage caused by over-tightening the 
fasteners. 
 
2: Any thread stripping, cross threading or thread damage of any kind will not be covered under our 
warranty. All threads are pre-tested. We use stainless steel fasteners which are extremely tough. 
 
3: All acrylic is carefully checked for scratches, marks or particles as the manifold is assembled. We 
are not responsible for mistreatment of the acrylic. Only clean with a microfiber cloth and use nothing 
except distilled or deionized water for cleaning, or Novus Plastic Cleaner. Damage caused by cleaning 
agents (particularly alcohols or solvents) is not covered under warranty. 
 
4: Acrylic Surface Guarantee: Marks on acrylic which cannot be wiped away with a microfiber cloth 
will only be covered under warranty under the following conditions: That they did not occur after the 
item was shipped from the Singularity Computers Factory or Retailer. If there are more than 10 marks 
which are beyond 5mm in length and visible when facing perpendicular to the surface. Evidence of 
this must be photographed in detail and photographs must be taken perpendicular to the surface. 
Marks must be easily visible in photographs; subtle marks will not be covered. 

5: For the latest coolant recommendations please visit 

http://bit.ly/sc-important-info

We are not 

responsible for staining of the acrylic, but it has never been an issue with our products. Most staining 
will be easy to remove by flushing out the loop with distilled water for 24hrs or using Mayhems Blitz. 
If you are concerned about staining then we suggest Mayhems Non-Stain Dyes. 

6: Any damage which occurs after the item leaves the Singularity Computers Factory or our Retailers 
is not covered under warranty. We are not responsible for shipping damage or mishandling.

 

 

Summary of Contents for WRAITH 2.0


















Reviews: