SINGULARITY COMPUTERS WRAITH 2.0 Manual Download | Manualshive

Page: 9 / 17

background image

Revision 1.00

8

Assembly Tolerances & Alignment

Wraith 2.0 uses CNC machining and very thick materials. This means it is manufactured with
extreme precision and there is no flex or play in any of the materials. Due to this we have built in
tolerances to most mounting holes to allow for the looser tolerances on the components being
installed. If a component does not align then loosen the related fasteners and you will be able to
align it. All of the outer panels have a tolerance built in so that they can be used for alignment
also.

Tools Required

•

M4 Allen Key

•

6-32 Hex Key

•

M3 Allen Key

•

Fill & Drain Tubes

Note: Tools listed are not included, unless otherwise specified.

«
...
7
8
9
10
11
...
»

Summary of Contents for WRAITH 2.0


















Reviews:

No comments

Related manuals for WRAITH 2.0

Brand: OBERON Pages: 2

Brand: Hartmann Pages: 8

Brand: Apevia Pages: 12

Brand: Siemon Pages: 4

Brand: TOOQ Pages: 22

Easydata 3.5" HDD Series

Brand: TOOQ Pages: 20

Opticube VSOF-BS606G

Brand: VISSEM Electronics Pages: 2

Brand: RAID Pages: 15

Icy Box IB-287-C31

Brand: RaidSonic Technology Pages: 8

Brand: Vantage Hearth Pages: 6

USB 2.0 2.5" SATA HDD MAC Enclosure

Brand: Hama Pages: 12

Brand: molex Pages: 3

Brand: Salsbury Industries Pages: 5

Brand: Honeywell Pages: 16

Brand: RAK Pages: 5

dark base pro 900

Brand: BE QUIET! Pages: 8

817A LF SPEAKER CABINET

Brand: Altec Lansing Pages: 2

Brand: Crate Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands