background image

6

7

CATCHING THE BOBBIN THREAD

1.  Raise the presser foot by pulling up the Presser 

Foot Lifter.

2.  Hold the top thread 

(A)

 and turn the Handwheel 

toward the front of the machine to make the needle 

go down and back up. You will see a loop formed by 

the bobbin thread 

(B)

.

3. Pull the loop to find the end of the bobbin thread.
4.  Pull ends of both threads to the back of the machine 

(C)

 and slide the Bobbin Case Cover back into place.

 You are now ready to start sewing.

A

B

C

CHANGING THE NEEDLE

Caution: 

When changing the needle, make sure the device is in 

LOCK

/OFF position.

1. Raise the needle to its highest position.
2.  Hold the needle and loosen the Needle Clamp Screw 

(E)

. Remove the old needle.

3.  Insert the new needle into the clamp with the flat side 

toward the right of the machine making sure the eye 

is straight facing the right or the left of the machine. 

Be sure to push the needle all the way up into the bar 

before tightening the Needle Clamp Screw 

(E)

.

4. Tighten the Needle Clamp Screw.

Please note: 

After replacement of the needle, first move 

Handwheel toward the front of the machine to check if 

there are stitches, and then operate machine by power 

ONLY WHEN THE NEEDLE IS IN RIGHT POSITION AND 

THERE ARE STITCHES BEING FORMED.

IMPORTANT:

 Safely store and dispose of used machine 

needles (pins and other sharp objects) in a container to 

prevent them from becoming loose in the trash, and then 

place the container in the garbage.

TROUBLESHOOTING POSSIBLE CAUSES 

OF POOR STITCHES

1.  The upper threading is not correct.
2.  The presser foot is not in the down position.
3.  The needle is not fully inserted in the needle bar.
4.  The needle eye is not facing the right or the left of the machine.
5.  The needle is bent.
6.  Lower threading is not correct.
7.  The wrong size bottom bobbin is used.
8.  Upper threading is too loose.
9.   The bobbin placement in case is not in the right position which will block its 

correct movement.

This appliance is not intended for use by person (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the device by a person responsible for 

their safety.

Children should be supervised to ensure that they do not play with the device.

E

Summary of Contents for Stitch Quick+














Reviews: