background image

28

第六章

 

操作控制显示面板

 

AC operation mode

: to set the operation mode, constant power or constant inactive power. 

PF:

 set to regulate the PF of the entire storage system 

Power configuration: 

Set to

 

regulate the power of the storage system

 

Q configuration: 

Set to

 

regulate the inactive power of the storage system

 

Grid reconnection delay

: please keep the default configuration.

 

Normal ramp rate

: please keep the default configuration. This function will apply when set power changes. 

The default value is 2 rated power per second, which means within 0.5 seconds the system can runs to full 
output. 

Soft-Start/Reconnection ramp rate

: please keep the default configuration. This function will apply when 

system suspend happens caused by utility voltage abnormal, and reconnect after utility restore normal. The 
default value is 2, twice of rated power per second, which means within 0.5 seconds the system restores to 
full output. 

Off-grid V range

: to regulate the off-grid output voltage.

 

P Change mode

: to set the power change pattern, step-to-top, or ramp-rise.

 

Ground-fault detection

: enable or disable ground-fault detection.

 

Anti-Islanding

:  enable  or  disable  anti-islanding  function.  For  more  information,  please  refer  to  UL1741 

Supplement A or other similar rules about Utility-Interactive Distribute Generators . 

Off grid start mode

:

 

Can be set as step-to-top, or ramp-rise. 

Active power regulation

: enable or disable active power regulation.

 

6.5.4.1 

FVRT 

FVRT

: frequency/voltage ride-through, this function can be enabled or disabled, for more information, please 

refer to UL1741 Supplement A or other similar rules about Utility-Interactive Distribute Generators . 

O/UVR* protect voltage:

 to set the over/under voltage ride though protect voltages.

 

O/UVR* trip time:

 to set the over/under voltage ride though trip times. 

O/UFR* protect frequency:

 to set the over/under frequency ride though protect frequencies.

 

O/UFR* trip time: 

to set the over/under frequency ride though trip times.

 

6.5.4.2 

Volt/Var 

Volt/Var regulation is only available when enabled. In Volt/Var mode, the Q configuration is disabled. 

Volt/Var point:

 to set the Volt/Var switch point. 

When the actual voltage between Volt/Var point 1 and 2, the capacitive inactive power will be increased.   
When the actual voltage between Volt/Var point 3 and 4, the inductive inactive power will be increased. 
For more information, please refer to UL1741 Supplement A or other similar rules about Utility-Interactive 
Distribute Generators . 

Max inductive reactive regulation

:

 

to set the maximum inductive reactive power regulation. 

Max capacitive reactive regulation

: to set the maximum capacitive reactive power regulation.

 

6.5.4.3 

Volt/Watt 

Volt/Watt regulation is only available when activated and operating in discharge mode. When the actual voltage is above the 

point, the active power will be regulated with the ramp rate. The ramp rate is defined as multiple of set active power per 1% of 

rated voltage that above the Volt/Watt point. 

Volt/Watt point

: to set the Volt/Watt trigger threshold.

 

Volt/Watt ramp rate

: to set the ramp rate when Volt/Watt is triggered.

 

Volt/Watt delay

: to set the output power restore time delay after the utility voltage restores normal. 

6.5.4.4 

Freq/Watt 

Available when activated and operating in discharge mode. When the actual frequency is above the point, 

Summary of Contents for PWS1-500KTL-NA


















































Reviews: