Adjustment of End limits
2
47
47
659
5
672
695
585
5
598
621
T
min.
A
(mm)
ØB
(mm)
L1
(mm)
L2
(mm)
A
4xØB / 90
T5E
230V~50Hz
08/17 • 10/17 • 15/17
20/17 • 25/17 • 35/17 • 50/12
L1
L2
4
55
IP44
Blue
Brown
Black
Green/yellow
PE
L
N
230V~50H
z
>>
1
OK
1
2
3
>>
2
Drilling of the tube:
Assembly :
2.1. Connect the motor to the settings switch
(réf.: 2006024)
. This switch is specific to T5E / T5E-SP /
T6E-SP motors.
Do not under any circumstances use
it with another motor!
2.2. Check the rotation direction:
- Connect the switch to the mains, then press ▲ :
1. If the tube turns in the "up" direction, go to step 2.3.
2. If the tube turns in the "down" direction, invert the Brown
(2) and Black (3) wires on the motor, and repeat the test.
During the End limits adjustment, there is a
one-second
delay in motor operation.
2
3
1
5
4
Ø4,8 x 10
Ø5 x 10
STEEL
25Nm max.
9910013
9910014
1
35Nm max.
Installation
1
-20°C / +60°C
These instructions apply to all T5E drive, the different versions of which are available in the current catalogue.
Field
: T5E drive are designed to all types of roller shutters. The installer, who must be a motorisation and home automation professional,
must ensure that the drive product is installed in accordance with the standards in force in the country in which it is installed such as
EN 13659 relating to roller shutters.
Liability
:
Before installing and using the drive, please read operating and installation guide carefully. Please read these ins-
tructions carefully before installing and using the drive.
In addition to following the instructions given in this guide, the instructions
detailed in the attached Safety instructions document must also be observed. The drive must be installed by a motorisation and home
automation professional, according to instructions from SIMU and the regulations applicable in the country in which it is commissioned.
It is prohibited to use the drive outside the field of application described above. Such use, and any failure to comply with the instructions
given in this guide and in the attached
Safety instructions
document, absolves SIMU of any liability and invalidates the warranty. The
installer must inform its customers of the operating and maintenance conditions for the drive and must provide them with the instructions
for use and maintenance, and the attached
Safety instructions
document, after installing the drive. Any After-Sales Service operation
on the drive must be performed by a motorisation and home automation professional. If in doubt when installing the drive, or to obtain
additional information, contact a SIMU adviser or go to the website
www.simu.com
.
Instructions which must be followed by the drive and home automation professional installing the drive:
- Methods of wiring are given by national standards or IEC 60364 standard.
- Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.
- The cable for the motor can be removed. If it is damaged, replace by the same. The cable may only be connected to the
motor by qualified personnel. The connector is to be assembled without damaging the contacts. The continuity of the earth
connection must be ensured.
1/3
i
EN-
Original instructions
5013732H
SIMU S.A.S. au capital de 5 000 000 €
Z.I. Les Giranaux - BP71 70103 Arc-Les-Gray CEDEX – FRANCE
RCS VESOUL B 425 650 090 SIRET 425 650 090 00011
n° T.V.A CEE FR 87 425 650 090
T5E
(230V~50Hz)
