44
DataMover ESS User’s Guide
SIMREX MAN.ESS-01, Rev. F
SIMREX Corporation
TIP:
For enhanced security, consider using misspelled words, a combi-
nation of letters and numbers, and a combination of upper and
lower case letters. Also, the Network Name should be at least nine
characters long. This helps protect against sophisticated hackers
who may use a database of common words (for example, dictio-
nary attacks) to determine the Network Name.
•
SNTP Server
—Address of SNTP server (RFC 2030) from which
the transceiver will automatically get the time-of-day startup
time. Without an SNTP server, the date and time must be man-
ually set. An AP will try to get the time and date from the SNTP
server only if an IP address is configured. It will continue to
retry every minute until it succeeds.
A remote will get the time and date from the SNTP server, if an
IP address is configured. Otherwise it gets it from the AP at
authentication time. The transceivers use UTC (Universal Time
Constant) with a configurable time offset. [
0.0.0.0
]
•
IP Address Configuration
—Presents a menu for configuring the
local static IP address of the transceiver. Detailed explanations
are provided in the section titled
IP Address Configuration
Menu
on Page 45
•
Ethernet Port Configuration
—Presents a menu for defining the sta-
tus of the Ethernet port (enabled or disabled), the Ethernet rate
limit, link hardware watch (enabled/disabled), and the Ethernet
link poll address. Detailed explanations of this menu are con-
tained in
Ethernet Port Configuration Menu
on Page 46
•
DHCP Server Config(uration)
—Menu for configuration of DHCP
services by the
Access Point unit. DHCP provides “on-the-fly”
IP address assignments to other LAN devices, including SIM-
REX
DataMover ESS
units. [
Disabled
]
•
SNMP Config Menu
—SNMP configuration parameters.
•
Mobility Mode
—Used to configure whether the transceiver is
enabled or disabled for mobility operation.
Note that this selec-
tion may appear on both Access Point and Remote menus, but it
only takes effect when set on Remotes.
Additional settings and
information for mobility operation are contained in
Mobile Data
Configuration
on Page 58
. [
enabled, disabled; disabled
].
•
Maximum Remotes
(AP Only)
—Number of Remotes permitted to
be associated with (served by) this Access Point. [
50
]
•
Database Timeout
(AP Only)
—This sets the database “age time”
(
Remote Listing Menu (Access Points Only)
on Page 93
) to
determine when a remote is declared as unavailable. The timer
may be set from 0 to 255 minutes and resets each time a message
is received from a remote. [
0–255 minutes; 5 minutes
]
Summary of Contents for DataMover ESS
