background image

5

SimpliFire  • SF-SC43-BK, SF-SC-55-BK, SF-SC78-BK   •  2041-980  •  1/19

     

Note:

  The device complies with Part 15 of the FCC Rules.  

Operation is subject to the following two conditions:
1.  This device may not cause harmful interference, and
2.  This device must  accept any interference received, 

 

    including interference that may cause undesired  

      operation.

MODELS:

 SF-SC43-BK, SF-SC55-BK, SF-SC78-BK

LABORATORY:  

CSA International

TYPE:  

Electric Air-Heaters; Fixed and Location-Dedicated  

             Electric Room Heaters

STANDARD:

 CSA C22.2 No 46-13; UL 2021 (4

nd

 Edition)

A.  Appliance Certification

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.  

This appliance is tested and approved as either supplemen

-

tal room heat or as a decorative appliance.  It should not be 

factored as primary heat in residential heating calculations.

NOTICE: 

This installation must conform with local codes. 

GENERAL INFORMATION 

  

B.  Unpacking and Inspecting Appliance 

WARNING!  DO NOT use this Electric Fireplace if  any 

part has been under water.  

Immediately  call  a  qualified 

service technician to inspect and to replace any part of the 

electrical system if necessary.  Keep plastic wrapping away 

from children.

•  Carefully remove the appliance and components from the 

packaging.  Discard packaging.

•  Carefully inspect components for any damage.
•  Reference parts list to verify all parts have been received.
•  Read all the instructions before starting the installation.  

Follow these instructions carefully during the installation to 

ensure maximum safety and benefit.

This equipment uses and can radiate radio frequency 

energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio 

or television reception, which can be determined by turn-

ing the equipment off and on.  The user is encouraged 

to try to correct the interference by one or more of the 

following measures: 
•  Increase the separation between the equipment and the 

receiver.

•  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

C.  Model and Serial Number Information 

 

The model and serial number information is located on the 

rating plate.  The rating plate is located behind the glass on 

the top interior surface of the viewing area. 

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________

Location on fireplace:

 _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

We recommend that you record the following pertinent 

information about your fireplace.

Homeowner Reference Information

ELECTRIC FIREPLACE

MODEL                   SF-SCXX-BK

VOLTAGE

FREQUENCY

AMPERAGE

WATTS

SERIAL No.:

MADE IN CHINA

249163

120V AC

60 Hz

12.5  A

1500 W

WARNING:  

This product can expose you to Di-

(2-ethylhexyl) phthalate, which is known to the 

State of California to cause cancer and reproductive 

harm.  For more information go to: www.P65Warnings.

ca.gov.

Summary of Contents for SF-SC43-BK






















Reviews: