background image

SimpliFire  • SF-SC43-BK, SF-SC-55-BK, SF-SC78-BK   •  2041-980  •  1/19

  

2

 

 

1

 IMPORTANT INSTRUCTIONS

 

  

WARNING!  Risk of Fire! Risk of Burns!

Risk of Electrical Shock!

DO NOT: 

• 

Install or operate damaged heater

• 

Modify heater

• 

Operate the heater without fully assembling all 

components

Hearth & Home Technologies Inc. disclaims any responsibility 

for, and the warranty and agency listing will be voided by the 

above actions. 

 

WARNING!  DO  NOT  operate  fireplace  before  reading  and 

understanding operating instructions. 

Failure to operate ap-

pliance according to operating instructions could cause fire or 

injury.

WARNING!  Improper  installation,  adjustment,  alteration, 

service or maintenance can cause injury or property dam-

age.  

Failure to install appliance according to Owner’s Manual 

could cause property damage or injury.  

NOTICE! 

This appliance is not intended for use as a primary 

heat source and should not be factored as such in residential 

heating calculations.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS 

When using electrical appliances, basic precautions should  

always be followed to reduce the risk of fire, electric shock, and 

injury to persons, including the following:

• 

Read all instructions before installing this appliance.

• 

This appliance is hot when in use.  To avoid burns, do not let 

bare skin touch hot surfaces.  Keep combustible materials 

such as furniture, pillows, bedding, papers, clothes, etc., and 

curtains at least 3 ft. (0.9 m) from the front of the appliance 

and keep them away from the sides and rear.

• 

Extreme caution is necessary when any appliance is used 

by or near children or other at risk individuals and whenever 

the appliance is left operating and unattended.

• 

Do not operate any appliance if it malfunctions.  Disconnect 

power at service panel and have appliance inspected by a 

certified electrician before reusing.

• 

Do not insert or allow foreign objects to enter any ventilation 

or exhaust opening as this may cause an electric shock or 

fire, or damage the appliance.

• 

To prevent a possible fire, do not block appliance connection 

fan air intakes or exhaust in any manner. 

• 

A heater has hot and sparking parts inside.  Do not use it in 

areas where gasoline, paint, or flammable vapors or liquids 

are used or stored.

• 

Use this appliance only as described in this manual.  Any 

other use not recommended by the manufacturer may cause 

fire, electric shock, or injury to persons. 

•     Do not operate any appliance with a damaged cord or plug 

or after the appliance malfunctions, has been dropped or 

damaged in any manner.  Return appliance to authorized 

service facility for examination, electrical or mechanical 

adjustment or repair.

•    Always use properly grounded, fused and polarized outlets.
•    Always use ground fault protection where required by 

electrical code.

• 

  To disconnect appliance, turn controls to “OFF” then turn off 

the circuit breaker. 

• 

  To  prevent  electrical  shock  or  fire,  always  use  a  certified 

electrician should new circuits be required. 

•    When transporting or storing the appliance, keep in a dry 

place free from excess vibration to avoid damage. 

• 

    To prevent possible fire, do not store or use gasoline or other 

flammable vapors and liquids in the vicinity of the heater.  

•    

 

Never locate appliance where it may fall into a bathtub or 

water container.

•      

AVOID FIRE!

  Regularly inspect all air vents to make sure 

they are free from dust, lint, or other blockage.  Turn off power 

by turning off the circuit breaker to

 

the unit and clean with a 

vacuum ONLY.  

DO NOT

 rinse or get wet.   

•      

NEVER

 hang this unit on a wall directly below an electrical 

outlet.

•      WARNING:

  Reduce the risk of fire or electrical shock - do   

 

 not use this heater with any solid state speed control devices. 

• 

    This product is not intended to be a primary heat source.  It 

 

 is for supplemental heat only.   

•      

INDOOR use only! 

 Never use this heater outdoors.  Doing 

so may result in electric shock. 

•      

Risk of electric shock!  DO NOT OPEN!

 No user-

serviceable parts inside.  

•     

 NEVER modify this heater.  

Doing so could result in 

personal injury or property damage.  Modification of this 

fireplace completely voids all warranties. 

•     

ALWAYS

 disconnect this unit from power supply before 

performing any assembly  or cleaning, or before relocating 

the electric fireplace. 

•     

NEVER 

leave this heater unattended.  

ALWAYS

 Turn off 

power by turning off the circuit breaker when heater is not 

in use. 

•    

 ALWAYS

 store this heater in a dry location.  NEVER use 

the fireplace if it has become wet. 

•    

 A minimum 15-Amp 120VAC circuit is required for this 

heater.  NEVER 

overload the circuit.  If the heater trips 

the circuit breaker, unplug all other appliances on the 

same circuit before the next use.  Avoid plugging other 

appliances into the same circuit as this heater. 

Summary of Contents for SF-SC43-BK






















Reviews: