Simplicity 5901597 Operator'S Manual Download

Page: 14 / 48

Not for

Reproduction

simplicitymfg.com

Callout

Control Name

Seat Adjustment Lever (Forwards /

Backwards)

Seat Adjustment Knob (Suspension/

Ride Comfort)

Lumbar Adjustment Lever (Located

underneath right hand arm rest)

Back Angle Adjustment Knob

Retractable Seat Belt

Seat Adjustment Lever (Forwards / Backwards):

The

seat can be adjusted forward and back. Move the forwards /

backwards seat adjustment lever, position the seat as

desired, and release the lever to lock the seat in position.

Seat Adjustment Knob (Suspension/Ride Comfort):

The

seat adjustment knob adjusts the suspension of the seat (ride

comfort). Turn the adjustment knob until the display scale has

a reading that matches the weight of the operator.

Lumbar Adjustment Lever:

Turn the lumbar adjustment

knob until the desired amount of lumbar is achieved.

Back Angle Adjustment Knob:

Turn the back angle

adjustment knob until the desired amount of back angle is

achieved.

Ground Speed Control Levers:

These levers control the

ground speed and direction of the rider. The left lever controls

the left rear drive wheel and the right lever controls the right

rear drive wheel.

Callout

Icon

Description

FORWARD

NEUTRAL

REVERSE

N/A

NEUTRAL LOCKOUT

POSITION

The parking brake must be disengaged before attempting to

move the ground speed control levers from the NEUTRAL

position.
Moving a lever forward (A) from the NEUTRAL position (B)

increases the FORWARD speed of the associated wheel, and

pulling back (C) on a lever increases the REVERSE speed.
Moving a levers outwards (D) from the NEUTRAL position

locks the levers in the NEUTRAL LOCKOUT position.

Note: The further a lever is moved away from the neutral

position the faster the drive wheel will turn.

See the

Zero-Turn Driving Practice

section for steering

instructions.

Fuel Selector Valve:

Turning the handle to the desired

position determines which tank will be supplying fuel. With

the handle pointing LEFT, it will draw fuel from the left-hand

tank. With the handle pointing RIGHT, it will draw fuel from

the right-hand fuel tank. With the handle pointing towards the

operator, it will shut off fuel flow to the engine.

Fuel Tank Cap:

To remove the cap, turn

counter-clockwise

Fuel Level Gauge:

Displays the fuel level in the tank.

Retractable Seat Belt:

The seat belt is used to secure the

operator to the seat.

Summary of Contents for 5901597

















































Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands

Simplicity 5901597, Operator'S Manual

Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands