Simplicity 5901597 Operator'S Manual Download

Page: 27 / 48

Not for

Reproduction

1. Warm the engine by running it for a few minutes.

Refer

to the engine operator's manual for oil filter and

replacement instructions.

2. Remove the oil drain hose (B) from its storage position

and route the hose so that when the oil drain cap is

removed the oil can be drained into a small pan.

3. Place a small pan under the oil drain hose to catch the oil.

Using the appropriate tools, remove the oil drain cap from

the oil drain hose and drain the engine oil.

4. After draining, replace the cap and wipe up any spilled oil.

Reinstall the oil drain hose to it's storage position so it is

retained during normal operation.

5. Place an absorbent shop cloth under the engine oil filter

(C). Remove the engine oil filter and replace with a new

one.

6. Add engine oil (refer to engine operator’s manual) in the

fill tube (D) and check the amount of oil in the engine

using the engine oil dipstick.

7. Remove the shop cloth and wipe up any spilled oil.

Disposing of Used Engine Oil

Used oil is a hazardous waste product and must be disposed

of properly. Do not discard with household waste. Check

with your local authorities, service center, or dealer for safe

disposal/recycling facilities.

Engine Maintenance

For engine maintenance schedules and procedures, please

refer to the engine operator's manual.

Electronic Fuel Injection (EFI) System -

EFI Models

EFI is an electronically-controlled fuel management system

which is monitored by an Electronic Control Unit (ECU). A

Malfunction Indicator Lamp (M.I.L.) will illuminate if problems

or faults are detected. Servicing by an authorized dealer is

necessary.

CAUTION

Do not disconnect or reconnect ECU wiring harness

connector or any individual components with the ignition

switch in the "ON" position. This can send a damaging

voltage spike through the ECU.
Unplug harness from ECU before performing any welding

on equipment.

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect

for damage or carbon blockage. If replacement parts

are required, make sure to use only original equipment

replacement parts.

WARNING

Replacement parts must be the same and installed in the

same position as the original parts or fire could result.

Fuse Location and Identification

The electrical system for this unit is equipped with two

replaceable fuses. See the chart below for the circuit,

amperage, and approximate location of the fuses.

Circuit

Amperage

Approximate Location

Main

25 amp

Instrument control

panel.

PTO Clutch

15 amp

Behind the seat on the

left hand side of the

machine.

Check / Fill Transmission Oil Level

This unit is equipped with two transmission oil tanks. One

transmission oil tank only supplies oil to one transmission.

The level of oil in both transmission tanks must be checked,

and if necessary, filled.

Oil Type:

SAE 20W-50 motor oil

1. Locate the transmission oil tanks (B, Figure 30) by raising

the seat plate of the unit.

2. Check the oil level when the unit is cold. The oil should be

up to the "FULL COLD" mark (A) on the transmission oil

tanks (B). If the oil is below this level, proceed to step #3.

Summary of Contents for 5901597

















































Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands

Simplicity 5901597, Operator'S Manual

Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands