Simplicity 5901597 Operator'S Manual Download Page 32 | Manualshive

Page: 32 / 48

background image

Not for

Reproduction

32

simplicitymfg.com

41

2. Wedge a wooden block (D) between the mower blade

and the mower deck housing to keep the mower blade

from turning and torque the blade mounting bolt to 120 ft.

lbs (163 Nm).

Seat Adjustment

The seat can be adjusted forward and back. Move the lever

(A, Figure 42) towards the left, position the seat as desired,

and then release the lever to lock the seat into position.

42

Seat Adjustment (Suspension Seat)

In addition to the forwards and backwards seat adjustment,

models equipped with a suspension seat can be adjusted for

suspension (ride comfort), lumbar support, and back angle.

43

Seat Adjustment Lever (Forwards / Backwards):

The

seat can be adjusted forward and back. Move the forwards /

backwards seat adjustment lever (A, Figure 43), position

the seat as desired, and release the lever to lock the seat in

position.

Seat Adjustment Knob (Suspension/Ride Comfort):

The

seat adjustment knob (B) adjusts the suspension of the seat

(ride comfort). Turn the adjustment knob until the display

scale has a reading that matches the weight of the operator.

Lumbar Adjustment Lever:

Turn the lumbar adjustment

knob until the desired amount of lumbar is achieved.

Back Angle Adjustment Knob:

Turn the back angle

adjustment knob until the desired amount of back angle is

achieved.

Ground Speed Control Lever Adjustment

The control levers can be adjusted in three ways. The

alignment of the control levers, the placement of the levers

(how close the ends are to one another) and the height of the

levers can be adjusted.

To Adjust the Handle Alignment

Loosen the mount bolts (A, Figure 44) and pivot the lever(s)

(C) to align with each other.

«
...
30
31
32
33
34
...
»

Summary of Contents for 5901597

















































Reviews:

No comments

Related manuals for 5901597

Brand: Greencut Pages: 68

Brand: Snapper Pages: 28

Brand: Yard-Man Pages: 5

Brand: Jacobsen Pages: 36

GRASS KEEPER 190 W

Brand: Garland Pages: 136

TURF TIGER STT61V-31KB-DF

Brand: Scag Power Equipment Pages: 78

Brand: Gardenline Pages: 24

Brand: Flymo Pages: 11

Z Master Professional 7500-D Series

Brand: Toro Pages: 80

DECK PARK 107 M HD EL - 4WD

Brand: Stiga Pages: 2

Brand: AL-KO Pages: 304

Brand: Earthwase Pages: 20

Brand: Spear & Jackson Pages: 2

Brand: Sabo Pages: 88

Brand: Sealey Pages: 4

Brand: Sealey Pages: 4

Brand: Murray Pages: 142

Brand: Murray Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands