Simplicity 5901597 Operator'S Manual Download

Page: 29 / 48

Not for

Reproduction

2. Open the transaxle’s bypass valves (see

Pushing the

Rider by Hand

for the location and function of the bypass

valves), start the engine, release the parking brake, and

slowly move the zero-turn rider’s ground speed control

levers in both forward and reverse directions (5 to 6

times), as air is purged from the unit, the oil level will

drop.

3. Stop the engine and engage the parking brake.
4. Close the transaxle’s bypass valves, start the engine,

release the parking brake, and slowly move the zero-turn

rider’s ground speed control levers in both forward and

reverse directions (5 to 6 times), as air is purged from the

unit, the oil level will drop.

5. Stop the engine. Remove the jack stands from

underneath the machine.

6. Repeat the process detailed above but with the unit's

drive wheels on the ground. The procedure should be

performed in an area free of any objects or bystanders.

It may be necessary to repeat the process detailed above

until all the air is completely purged from the system. When

the transaxles/transmissions operate at normal noise levels

and move smoothly forward and reverse at normal speeds,

then the transaxles/transmissions are considered purged.

Checking Tire Pressures

Tire pressure should be checked periodically, and maintained

at the levels shown in the Specifications chart. Note that

these pressures may differ slightly from the "Max Inflation"

stamped on the side-wall of the tires. The pressures shown

provide proper traction and extend tire life.

Lubrication

Lubricate the unit at the locations shown in Figures 32, 33,

and 34 as well as the following lubrication points:

Grease:

• front caster wheel axles & yokes
• deck lift pivot blocks
• mower deck spindles
• transmission cradle pivot points

Use grease fittings when present. Disassemble parts to apply

grease to moving parts when grease fittings are not installed.
Not all greases are compatible. Red grease (p/n 5022285)

is recommended, automotive-type, high-temperature, lithium

grease may be used when this is not available.

Oil:

• control handle pivots

• seat plate pivots
• deck lift pivots
• discharge chute hinge

Generally, all moving metal parts should be oiled where

contact is made with other parts. Keep oil and grease off belts

and pulleys. Remember to wipe fitting and surfaces clean

both before and after lubrication.

Summary of Contents for 5901597

















































Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands

Simplicity 5901597, Operator'S Manual

Search results

Summary of Contents for 5901597

Reviews:

Related manuals for 5901597

Brands by name

Popular brands